710 MMA Repair Mortar is a fast curing, high strength, trowel applied, three component methacrylate resin mortar, designed for rapid and permanent repairs to concrete and masonry surfaces.

The product is ideal for repairs to spalled or damaged concrete, bedding pre-cast concrete beams, chemical bunds and floor repairs.

This product is for Professional Use Only.

Quick Links - Click To Jump To Section:

• Features & Benefits
• Typical Properties
• Coverage
• Surface Preparation
• Application
• Cleaning
• Curing
• Limitations
• Storage & Shelf Life
• Health & Safety

Features & Benefits

• High strength
• Trowel applied
• Designed for rapid and permanent repairs to concrete and masonry surface
• Resilient
• Very good chemical resistance
• Excellent adhesion
• Fast curing, even at low temperatures (down to -10°C*)
• Impact and abrasion resistant
• Frost resistant and impervious to water
• Accepts foot trafficking after a minimum of 1 hour @ 20°C
• Three pack
• Excellent mechanical properties

*Please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected]

Typical Properties

*Please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected]

Coverage

• A 10kg pack yields 5 litres of mortar, sufficient for 1m² @ 5mm thickness

Surface Preparation

• Remove all laitance, spalled concrete, grease, oil, dust, and other contaminants by scabbling, bush hammering, or other mechanical treatment, to provide a sound clean substrate
• Any exposed reinforcing steel shall be fully exposed by cutting out around its full circumference, and cleaned by hand abrading or wire brushing to remove rust, scale, etc., and primed with a coat of 706 MMA Floor Primer

Priming:

• The prepared concrete surface, together with the pre-primed re-bars, shall be primed by the application of 706 MMA Floor Primer
• The mixed 706 MMA Floor Primer should be applied by brush or roller at a nominal rate of 0.2 – 0.3kg/m², depending upon surface profile
• Allow the primer to cure for a minimum of 40 minutes

Mixing:

• 710 MMA Repair Mortar is supplied as a three component product consisting of the base component, the catalyst component and the aggregate component
• The contents of the base and catalyst component should be thoroughly mixed together and the aggregate then introduced
• A low speed drill stirrer or a forced action mixer such as a Mixall, Pennine or Creteangle type, will be suitable

Mixing Ratio:

• (% Catalyst by Weight) = 2.5

Application

• 710 MMA Repair Mortar should be applied by tamping and trowelling to ensure good compaction and a tight finish
• The material should not be feather edged
• Minimum application thickness is 4mm

Cleaning

• Clean equipment with 109 Tool Cleaner immediately after use

Curing

• Allow a minimum cure time of 1 hour @ 20°C prior to foot trafficking and 2 hours @ 20ºC prior to full trafficking

Limitations

• Do not apply to wet, uncured or unprimed concrete surfaces

710 MMA Repair Mortar will taint food during application, so that all foodstuffs in the immediate vicinity must be removed or properly covered.

Storage & Shelf Life

• Store in dry conditions, out of direct sunlight, at temperatures between 10°C and 20°C
• Adequate ventilation of the storage area should be provided
• Keep container tightly closed when not in use
• 710 MMA Repair Mortar has a minimum shelf life of 6 months when stored in original, unopened containers in accordance with manufacturer’s instructions

Health & Safety

710 MMA Repair Mortar is flammable during application, so adequate safety precautions should be observed.

• Avoid contact of the material with skin and eyes
• Wear gloves and goggles
• Wash off splashes immediately with soap and water
• Any eye contamination must be rapidly irrigated with copious amounts of clean water, and immediate medical attention sought
• Please refer to Material Safety Data Sheet for additional information
• 710 MMA Repair Mortar shall be applied strictly in accordance with the manufacturer’s instructions

For specific advice regarding any aspect of this product, please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected]