Tremco SF115 Contact Adhesive is a one-part, modified elastomer contact adhesive for use with rubber and PVC. SF115 has been specially developed for contact bonding (two-way stick) of a wide range of floor coverings including: rubber tiles and sheet, vinyl and cork.
Also suitable for horizontal and vertical surfaces for bonding rubber/PVC nosing and covings
Extra strong bond
Extended working life
Fast drying but long ‘open time’
The dry bond does not support combustion
Coverage of approx. 2.5 - 3m² of bonded area per litre
Please note: Colours shown are approximate and are for illustrative purposes only
Please note this product is subject to a minimum order quantity
Site conditions MUST comply with British Standards CP 102, BS 8203, BS 5325 and supplementary specifications.
The surfaces must be sound, clean, dry and free from oil, grease, paint, dust and other contaminants liable to impair adhesion
Concrete and sand/cement screeds must be fully cured and free from laitance
Direct to earth subfloors must incorporate an efficient damp proof membrane
Underfloor heating must have been fully commissioned as per manufacturer's instructions and must be switched off 48 hours before and during installation
The heating should be switched on 48 hours after completion but then only gradually as per the commissioning schedule. Please contact Rawlins Paints Technical Department on 0113 2455450 (option 2) or send a message to [email protected] for more information.
Priming
Ensure substrate is suitable for the adhesive before application
Application
Stir the adhesive thoroughly before use and apply an even continuous coating, using a ‘V’ notched trowel size 1 mm x 4 mm
With some rubber floor coverings, it is recommended that the adhesive is applied to the floor with the ‘V’ notched trowel and to the back of the rubber with a flat spreader
Refer to the Flooring Manufacturer’s instructions
For vertical surfaces, a bristle brush application may be convenient
Allow the solvents to evaporate until the adhesive on both surfaces is ‘touch dry’. This may take approximately 5 to 45 minutes, according to prevailing conditions
Place the materials accurately into position and press firmly to exclude air and ensure overall contact.
On horizontal surfaces, roll in both directions using a 68kg flooring roller.
LIMITATION
This product is not suitable for use with certain types of PUR vinyl
Please check with the floor covering manufacturer
Technical Data:
Property
Result
Composition
A modified chloroprene elastomer dissolved in a blend of flammable solvents
Specific Gravity
0.82 - 0.86
Flash Point
Below -18°C
Application Temperature Range
+4°C to +30°C
Service Temperature
-20°C to +85°C
Coverage
2.5 - 3m² of bonded area per litre
Dry Tack Time
Up to 40 minutes after becoming touch dry
Drying Time
5 to 45 minutes
Final Bond Strength
36 to 48 hours
Storage
Store between +5°C and +27°C
Shelf Life
12 months from manufacturing date, when stored as recommended in original unopened containers
Please contact Rawlins Paints Technical Department on 0113 2455450 (option 2) or send a message to [email protected] for more information.
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Tremco SF115 Contact Adhesive is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
We no longer stock this product; please contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to find an alternative product. Tremco SF165 Water Resistant Contact Adhesive is a cross-linking contact adhesive used for the permanent bonding of smooth backed rubber floor...
Tremco AW421 Industrial Cleaner is a powerful solvent-based cleaning solution for dissolving and removing mastics, adhesives and sealants. AW421 will remove many common adhesives and sealants, particularly in the uncured state. The product may also be used for cleaning and to degrease other surfaces that are not sensitive to solvents, such as...