Watco Basics Pourable Repair Mortar is a quick and easy way to fill holes in concrete floors. This blended polymer and cement formulation is strong enough to resist heavy foot traffic, trolleys and trucks. Just take as much powder as you need out of the bucket, mix with water and pour – you don’t need a primer.
Just mix with water and pour
Takes traffic after only 4 hours
Non dusting, resists grease and oil
Repairs from 5mm to 100mm thick in one go
For areas where there is regular forklift traffic, see Watco Flowpatch.
The product ‘flows’ to fill the hole making it unsuitable for ramps, steps or broken concrete edges; please see Watco Concrex for this type of repair.
Watco Basics Pourable Repair Mortar is a quick and easy way to fill holes in concrete floors. This blended polymer and cement formulation is strong enough to resist heavy foot traffic, trolleys and trucks; (for areas where there is regular forklift traffic, see Watco Flowpatch). Just take as much powder as you need out of the bucket, mix with water and pour – you don’t need a primer.
The mortar will not shrink as it dries and will take foot traffic after only 4 hours and trucks and trolleys after 6 - 8 hours. The product ‘flows’ to fill the hole making it unsuitable for ramps, steps or broken concrete edges; please see Watco Concrex for this type of repair.
Only basic preparation is necessary. If the hole or patch to be repaired is just dirty and dusty, give it a good sweep. Watco Basics Floor Cleaner can be used to remove oil and grease, or grease and loose material can be removed from small patches using a stiff broom or wire brush.
Application
It does not matter if the floor has been left damp following any wet preparation
Dampen dusty, porous surfaces with water in hot, dry conditions
The mortar can be applied at any thickness between 5mm and 100mm. For deeper holes build up in layers, allowing the first layer of 100mm to dry for 12 hours
If the edge of the repair is less than 5mm deep, chip some concrete away so that the edge of the mortar repair will be 5mm thick. For feather edge repairs which go to nothing please see Watco Concrex
Remove the bag of powder from the Pourable Repair Mortar bucket
The mix is 1 part water to 4 parts powder
Only mix as much as you can use in 15 minutes. A cup can be used to measure the parts of water and powder
Put the water into the plastic bucket
Gradually add the powder mixing continuously. We recommend a mixing blade fitted into an electric drill. The ratio of water to powder is not critical, you just want the mix to be a consistency which can be poured. If it looks too runny add more powder, or too stiff, more water
Once you’ve stopped mixing and started using the product do not re-mix it
Immediately pour into the hole using a trowel to ‘help’ smooth the mortar into place
Application
Not recommended on slopes, steps or broken concrete edges
Resists oils and grease but not chemicals (see Watco Concrex)
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Watco Basics Pourable Repair Mortar is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
Rapid set concrete repair mortar for heavy wear, cold areas, that can be applied at 50mm thick at -20°C. Ideal for use in cold stores, securing railings, poles and posts, roads and manhole frames, etc.Easy to use – just add water, mix, and apply Starts to harden in 10 minutes, fully hard in five hours when suitably insulated (at -10°C)...
Quick setting, pourable repairs for filling holes in heavily trafficked concrete floors, inside and out. Ideal for filling deep holes before screeding with Watco Flowtop.Flowpatch and Flowpatch Coloured Easy to use rapid dry formula Takes forklifts in just 2 hours Just add water, mix and pour Fibre reinforced for added strength...