A two-part epoxy with pre-blended aggregate for an even, easy clean, fine anti slip finish for floors - concrete, sand and cement, wood, and existing, well-bonded paint. Available in 190 RAL shades Watco's strongest water-based epoxy coating Pre-blended aggregate for an even finish Fast curing – apply two coats in one day Easy clean,...
Watco Flowpatch Repair Bundle Pack
Everything you need for quick repairs to holes in concrete - quick setting, pourable repairs for filling holes in heavily trafficked concrete floors, inside and out. Ideal for filling deep holes before screeding with Watco Flowtop.
- The bundle includes:
- Flowpatch 25kg (Grey)
- Mixing Blade - for thorough mixing of Watco Flowpatch
- Steel Float - for a smooth finish
- Easy to use rapid dry formula
- Takes forklifts in just 2 hours
- Just add water, mix and pour
- Fibre reinforced for added strength
- Cold-curing version also available
Note: While great care is taken with the colour samples shown, no guarantee can be given that they represent exactly the colours offered.
Watco Flowpatch is an easy to mix pourable material for quick repairs to level concrete, inside or outside. Watco Flowpatch is very strong and hardens quickly: it will accept heavy traffic including forklifts only 2 hours after application.
Watco Flowpatch will resist oils and grease. If greater chemical resistance is required, please use Watco Concrex.
It can be applied at any depth between 5mm -100mm and repairs can be feather edged in light traffic areas. When mixed, Watco Flowpatch will be pourable so is not suitable for repairs to sloping floors or exposed edges.
After curing, Watco Flowpatch can be painted with any suitable Watco floor paint. If the floor being repaired is very rough, you may wish to screed the whole floor with Watco Flowtop for a smooth flat surface before painting.
The surface is inherently anti slip in dry conditions. Overcoating with Watco Safety Grip is recommended if positive anti slip is required in very wet or oily conditions. Watco Safety Coat is available where a general level of slip resistance is required.
Watco Flowpatch Typical Compressive Strength at 20°C:
- 1 day: >20N/mm2
- 7 days: >35N/mm2
- 28 days: >45N/mm2
Quick Links - Click To Jump To Section:
- Areas of use include:
- Ideal for filling deep holes before screeding with Watco Flowtop
- Just add water, mix, and pour
- Can be applied to damp (not wet) concrete
- Sets at low temperatures (down to 5°C)
- Can be applied at any depth between 5mm -100mm
- Slip resistant finish
- Fibre reinforced
The substrate should be clean and free from oil or contaminants. Any loose material should be removed from the surface. If possible, wire brush the surface. Edges of the repair should be cut to depth to avoid feather-edging in heavy wear areas. Watco Flowpatch can be applied to damp (not wet) concrete.
Remove the bag of powder from the plastic bucket and use the empty bucket or other suitable container for mixing. If using Flowpatch Coloured add the pigmented powder at this point, at a ratio of 24g per 1kg of Flowpatch powder (600g bag per 25kg). To achieve a pourable mix, add 3 parts of powder to one part of water (by volume).
Due to the short working life of the mixed product, we recommend you carry out the mixing near to the repair, not near to the water source. It’s also useful to have a bucket of water nearby, so you can quickly immerse and clean the tools after use.
Put the water into the empty bucket or container and gradually add the powder stirring constantly to achieve a pourable slurry. For small quantities mix by hand using a flat bladed tool such as a spatula, and for larger quantities use a mixer fitted into a slow speed electric drill (Watco Flowtop mixer is ideal). Do not add excessive water or drying time will be extended and the performance may be impaired.
As the mixture hardens quickly, pour the Flowpatch into the hole to be repaired immediately.
We do not recommend re-stirring as this could potentially weaken the final repair. Do not mix more than you can use within a few minutes (5-10 minutes at 20°C).
The remaining powder can be stored for future use.
When a smooth consistency is achieved, simply pour Watco Flowpatch into the hole. If the product has been properly mixed it will self-level and will need minimal trowelling. Watco Flowpatch can be applied in any depth between 5mm and 100mm. Repairs in lightly trafficked areas can be feather edged, but thin edges are not recommended for medium or heavily trafficked repairs.
- For Use By
- Consumer Use
- For Use By
- Industrial Use
- For Use By
- Professional Use
- Interior / Exterior Use
- Interior and Exterior
- For Use On
- Pack Size
- Approximately 0.5m2 at 25mm thick
- Recommended Thinner/Cleaner
- Remove excess with a cloth or scraper and wash with water before the product sets.
- Layer Thickness
- 5mm -100mm
- Pot Life
- Approximately 5 to 10 minutes at 20°C, so do not mix at one time more than you can use within a few minutes.
- Suitable For Use On
- Concrete Floors
- Suitable For Use On
- Product Range
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Watco Flowpatch Repair Bundle Pack is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
A three-pack epoxy resin coating designed to provide a safe surface, both inside and out, for steps, ramps and floors, in wet or oily areas. Coarse anti slip finish reduces accidents. Heavy duty with excellent chemical resistance Slip resistant even when wet or oily Easy one coat application for concrete, metal or wood Quick drying in as...
Quick setting, pourable repairs for filling holes in heavily trafficked concrete floors, inside and out. Ideal for filling deep holes before screeding with Watco Flowtop. Flowpatch and Flowpatch Coloured Easy to use rapid dry formula Takes forklifts in just 2 hours Just add water, mix and pour Fibre reinforced for added strength...
Watco Flowtop is designed as an industrial grade overlay for rough, damaged or tamped concrete. It cures to a smooth, non-dusting surface that is tough enough to withstand forklift trucks and can be left as a highly practical industrial finish or overpainted. Large areas of uneven, damaged and unsightly floors can be re-surfaced quickly and...