- There are no more items in your cart
- Shipping Calculated at checkout
- Sub-Total(ex. VAT)(inc. VAT)£0.00£0.00
We no longer stock this product, but can recommend Fosroc Lokfix S25 as a great alternative.
Please note: it is important to check that any alternative product is suitable for your requirements, as our suggestion is given in good faith but without warranty. If you are in any doubt please first contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to discuss your project.
A versatile epoxy resin grout with outstanding adhesion and strength, for permanently holding fixings and bolts in place.
- Two part epoxy resin grout
- Outstanding strength and adhesion
- Excellent chemical resistance to acids and oils
- Provides reliable fixings for rails, bolts and posts
- Hardens in one hour and may be stressed after 24 hours
Watco High Strength Epoxy Resin Grout is ideal for filling voids and cracks or providing a reliable fixing for bolts, railings, posts etc.
The outstanding adhesion and strength properties of this 100% solids epoxy resin will hold machinery fixings and sole-plates permanently in place. The product can be used to anchor machinery which vibrates in use.
Quick Links - Click To Jump To Section:
Features & Benefits
- High tensile and compressive strength
- Hardens in one hour (may be stressed after 24 hours)
- Negligible shrinkage
- Excellent chemical resistance
- No primer required
- Solvent-free
- Excellent resistance to spillages of a wide range of chemicals including dilute acids, alkalis, oils and petrol
Surface Preparation
Holes should be clean and sound. Avoid drilling out using a diamond drill since this leaves a very smooth finish. Surfaces should be dry. The product will be less successful in shallow holes with sloping sides.
Mixing
Remove the tin of curing agent from the bucket. Mix the loose sand and resin together in the bucket using a flat bladed palette knife or similar. Add the curing agent and mix thoroughly until uniform. Use immediately.
Application
Pour into the prepared hole. If inserting bolts etc, do so with a twisting action to prevent air pockets. Supports may be required until the product has hardened.
The product will be hard to the touch after approximately 1 hour.
Allow at least 24 hours before carefully tightening bolts.
Full cure and full strength are achieved after 7 days after which machinery etc may be installed.
Curing times assume a temperature range of 15-20ºC or above.
Lower temperatures will extend curing times. The product may not cure correctly if used at temperatures of less than 5ºC.
Strength Properties
Tensile strength > 30Mpa at 20°C
Compressive Strength > 60Mpa at 20°C
Data sheet
- Manufacturer
- Watco
- For Use By
- Consumer Use
- Interior / Exterior Use
- Interior & Exterior
- Water / Solvent Based
- Water
- For Use On
- Concrete
- Application Method
- Medium pile roller
Cut in using a brush - Single, Two or Three Pack
- Two-pack
- Pack Size
- 2KG
- Touch Dry (at 20°C)
- Approximately 1 hour
- Fully Cured (at 20°C)
- Allow at least 24 hours before carefully tightening bolts.
After 7 days after which machinery etc may be installed - Pot Life (at 20°C)
- Approximately 15 minutes
The mixed components can become quite warm if not used immediately. - Coverage
- 2kg of this product has the volume of approximately 1 litre (0.001m3).
As a guide this would fill at least 30 holes 25mm diameter x 50mm deep. - Recommended Thinner/Cleaner
- A strong solvent may be used.
- Min. Application Temperature
- 5°C
- UN Number (Activator)
- UN2735
- UN Number (Base)
- UN3082
- Resistance to chemicals
- Alkali
- Resistance to chemicals
- Petrol
- Resistance to chemicals
- Dilute Acids
- Resistance to chemicals
- Oil
- Base Type
- 100% Solids
- Suitable For Use On
- Workshop Floor
- Suitable For Use On
- Concrete
- Suitable For Use On
- Concrete Floors
- Suitable For Use On
- Garage Floors
- Suitable For Use On
- Factory Floors
- Suitable For Use On
- Floors
- Suitable For Use On
- Previously Painted Floors
- Suitable For Use On
- Warehouse Floors
- Product Usage Type
- Repair
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Watco High Strength Epoxy Resin Grout is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT