Sika Galvashield XP Galvanic Anodes are used in concrete rehabilitation to prevent the formation of new corrosion sites adjacent to completed patch repairs. The anodes quickly and easily fasten to the exposed reinforcing steel. Once installed, the zinc core corrodes preferentially to the surrounding rebar, thereby providing galvanic corrosion prevention...
Sika Rapid Repair Mortar
Sika Rapid Repair Mortar is an R4 fast setting cementitious repair mortar. Sika Rapid Repair Mortar is a one component fast setting cementitious repair mortar, meeting the requirements of Class R4 of BS EN 1504-3. Repairs all types of structures.
Sika Rapid Repair Mortar is a one component fast setting cementitious repair mortar, meeting the requirements of Class R4 of BS EN 1504-3.
- For repairing all types of structures
- Horizontal and vertical repairs
- Hand applied repairs
- Floor slabs and car park decks
- For exterior and interior use
- In place of R1, R2 & R3 mortars
Features and benefits:
- Pre-bagged for quality
- Just add water
- High early strength
- Rapid setting
- Contains no chloride admixtures
- Non corrosive to steel
- Can be overcoated
For more details please download the product data sheet from the 'DATASHEETS' tab above.
|Carl crouch on 03/11/2018|| |
What is the drying time on this product and can it be used in damp conditions
Sika Rapid Repair Mortar can be applied manually using traditional techniques. Thoroughly pre-wet the prepared substrate a recommended 2 hours before application. Keep the surface wet and do not allow to dry. Before application remove excess water e.g. with a clean sponge. The surface shall appear a dark matt appearance without glistening and surface pores and
Protect the fresh mortar immediately from premature drying for a minimum of 3 days using an appropriate curing method e.g. curing compound, moist geotextile membrane, polythene sheet etc.
Please refer to the Product Data Sheet for full details which can be downloaded from the 'Download' section on the product page.
|Karl on 29/11/2016|| |
Question: What temperature does it have to be to lay R4 rapid set mortar outside on concrete stairs
Rust-Oleum Pegacrete is a quick hardening, powdered repair product based on cement base and resins for indoor and outdoor works. Rust-Oleum Pegacrete should be used for levelling and repairing cracks, holes and other damages in concrete, cement renderings and not painted brickwork. 100% shrink resistant, good mechanical strength, easy to apply - just add...
Rust-Oleum Epoxyshield Concrete Repair Mortar is for levelling and repairing cracks, holes and other damages in concrete, cement renderings and not painted brickwork: Just add water, stir and its ready for use Light traffic possible after 24 hours (at 20°C) To recoat after 48 hours Sandable to a smooth finish For horizontal and vertical use FREE...
Sikadur 41 CF Rapid is a moisture tolerant, thixotropic, structural three part adhesive and repair mortar, based on a combination of epoxy resins and special fillers, designed for use at temperatures between +5°C and +20°C. Hardens without shrinkage, no primer needed, can be used for vertical and overhead applications (low sag), easy to mix and apply,...
Sika Armorcrete is a flowable cementitious micro-concrete. Sika Armorex Armorcrete is a one part, flowable, cementitious, micro-concrete repair system, which can be used for shuttered repairs and grouting.
Sika MonoTop 612 is an R4 hand placed/wet spray repair microconcrete. Sika MonoTop 612 is a cement-based, one component low permeability repair microconcrete, containing silica fume and polymer, meeting the requirements of Class R4 of BS EN 1504-3.
SikaMix Powdered Mortar Plasticiser (PMP) is a pre-measured air entraining admixture which complies to EN 934 and replaces or complements the use of lime in sand and cement bricklaying and rendering. Ready to use sachets, improved workability, increases durability, reduces shrinkage, increases frost resistance, use 1 sachet per 25kg of cement.
Sika 2 Water Plug is a rapid setting, leak stopping solution that is ready to use even on high waterpressure areas. It can be used to seal against high water pressure infiltrations and allows Sika 1 Waterproofing Renders, SikaCem 133 Gunite or Shotcrete to be applied on structures exposed to running surface water.
Sika X-Plug is a mechanical plug specifically designed to seal the void formed in a concrete wall by the removal of a tie bar. To fit tie bar size: 19.05mm – 25.04mm (¾ inch to 1 inch diameter) 11mm (7/16 inch) fixing nut. Quick and easy to install, secure mechanical plug, highly chemical resistant, can be installed from either side of tie bar hole, no...
Sikadur 41 CF Normal is a thixotropic, three part patching and repair mortar, based on a combination of epoxy resins and special fillers, designed for use at temperatures between +10°C and +30°C. Ideal for use with concrete elements, hard natural stone, ceramics, fiber cement, mortar, bricks, masonry, steel, iron, aluminium, wood, polyester, epoxy and glass.
Rust-Oleum Asphalt Repair Tamper is a 4.5 Kg square tamper with a 1370 mm steel shaft which ensures the optimum application of Rust-Oleum Asphalt Repair. An asphalt tamper allows the user to work in confined areas of limited space, and corners, where machines and other tools may not easily be able to access.
203 Deep Fill Repair Mortar is a versatile, trowel applied, three component Epoxy resin-based, deep section screed/mortar for economical, fast setting repairs to deeper section areas. The product is supplied in a concrete grey colour, and may be sealed or topped with a range of our epoxy floor coatings or sealers as required.
Sikadur 12 Pronto is a fast curing, self smoothing two part resin mortar based on reactive acrylic resins. Sikadur 12 Pronto is a fast curing multi purpose repair mortar for concrete roadways, runways, car park decks, industrial floors, stairs, precast concrete units etc. Can also be used as a grout for bridge bearings, foundations and rails, anchors and...