Rust-Oleum Epoxyshield Concrete Repair Mortar is for levelling and repairing cracks, holes and other damages in concrete, cement renderings and not painted brickwork:
Rust-Oleum Epoxyshield Concrete Repair Mortar is for levelling and repairing cracks, holes and other damages in concrete, cement renderings and not painted brickwork:
Features & Benefits
Just add water, stir and its ready for use
Light traffic possible after 24 hours (at 20°C)
To recoat after 48 hours
Sandable to a smooth finish
For horizontal and vertical use
10kg for 0.4m² (2cm thickness)
FREE trowel included
Powdered repair product on cement base and resins for inside and outside use.
Surface Preparation:
On bare substrate: clean with steel brush or sand blaster. The substrate must be solid and free from dust, oil and grease.
Mixing & Thinning: Mixing ratio: Approximately 5 parts of powder to 1 part of water (2 litres of water for the entire 10 KG). Fill the container with the water. Add the dry mortar to the water whilst stirring. Mix water and powder thoroughly to a thick smooth, lump-free substance. Add some water to your liking if the mortar is too dry.
Application: Apply the product with the included trowel or spatula up to a maximum layer thickness of 2 cm. Wet the trowel to smooth out any trowel marks or irregularities. After 48 hours the surface can be sanded using a rough sandpaper (P120) to obtain a smooth end result.
Cleaning of Equipment and Spills
Water
Remarks
The mortar can now be over coated with EpoxyShield coatings or other non-alkyd paints like Epoxies, Acrylics, etc. If thicker layers are necessary (> 2 cm) the mortar can be mixed with kiln dried quartz sand. Mixing ratio: 1 volume part mortar plus 0,3 to 0,5 volume parts of kiln dried quartz sand (0 - 4 mm).
Please contact Rawlins Paints' Technical Support Team on 0113 2455450 for more information.
Product Details
576-40890
Data sheet
For Use By
General Use
For Use By
Industrial Use
For Use By
Professional Use
Interior / Exterior Use
Interior & Exterior
Water / Solvent Based
Water
For Use On
Concrete
Application Method
Trowel
Colour
Standard / Ready Mixed
Single, Two or Three Pack
Single
Single, Two or Three Pack
Single
Pack Size
10KG
Dry to Recoat (at 20°C)
1 Days
Fully Cured (at 20°C)
1 Month
Coverage
0.4m² per 10KG
Min. Application Temperature
5°C
Density
1,6
VOC
0 g/
Shelf Life (from date of manufacture)
1 years from date of production in unopened cans, if stored in dry, well ventilated areas, not in direct sunlight at temperatures between 5° and 35°C.
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Rust-Oleum Hard Hat 2169/2182 Anti-Rust Primer is to be used on new, bare or slightly rusted steel surfaces to prevent further rusting and corrosion.
Ready to recoat after just 10 minutes, to handle after 30 min.
Penetrates deeply into the surface and does not give rust a chance
Grey for light coloured topcoats and red for dark coloured...
Rust-Oleum 3369/3380 CombiPrimer Anti-Corrosion is a high quality anti-rust primer for Rust-Oleum CombiColor. The Anti-Corrosion Primer will ensure an even longer anti-rust protection on new or rusted steel surfaces and provides and enhances protection against corrosion.
Recoatable after 2 hours
For new / slightly rusted surfaces
Grey for...
Repair Materials Application Kit provides everything you need to apply our repair products to floors, walls and other surfaces. It makes on site application much easier by providing everything you need to mix, prepare, apply and clean up in one handy kit.
Each Kit Contains:
4 Rubble Sacks for Waste
750ml White Spirit
10" Steel Float
6"...