

Keim Brillantputz-Rille is a high quality, mineral thin layer, lightweight grooved render made from mineral binders and high-quality fillers. Suitable as a finishing render for all level mineral substrates and as a top coat for Keim Universal Render. Suitable for subsequent application of Keim Mineral Paints.
Keim Brillantputz-Rille is a high quality, mineral thin layer, lightweight grooved render made from mineral binders and high-quality fillers. Suitable as a finishing render for all level mineral substrates and as a top coat for Keim Universal Render. Suitable for subsequent application of Keim Mineral Paints.
Substrate Preparation
All loose, flaking and unstable material must be identified and then thoroughly removed, all surfaces must be thoroughly washed down with clean cold water to remove all surface dirt and dust. When all surfaces are clean, sound, wind dry, dust free and free from all surface contaminants, application of KEIM Brillantputz Rillenputz may proceed.
Application
Initially use approx. 5 litres of water for 1 sack (25kg) and increase the amount of water until the render shows a creamy consistency, but not more than 7.5lt per bag. Mix using a mechanical stirrer or plaster mixing machine/sprayer, e.g. Putzmeister or similar. After a waiting time of a few minutes stir again briefly. Apply the prepared KEIM Brillantputz Rillenputz with a stainless-steel trowel, flatten or scrape down to grain size and rub in using a plastic trowel. To prevent streaking always work wet on wet. Always work with the same batch number in one area.
Machine Processing
KEIM Brillantputz Rillenputz can be mixed using a continuous mixer. The amount of water should be adjusted according to the processing consistency. Prior to manual application, stir again briefly using a mixer to achieve the required consistency. Mortar pumps with variable flow rates are suitable for the machine application of render mixed in a continuous mixer. After application the render should be floated or scraped down to the grain size and rubbed immediately with a plastic trowel.
Application Conditions
Ambient and substrate temperature above 5°C and below 30°C. Do not apply in direct sunlight or onto sun-heated surfaces, nor if it is raining or if there is an immediate likelihood of rain.
Consumption
Grooved render 2 mm: approx. 2.5 kg/m²
Grooved render 3 mm: approx. 3.0 kg /m²
The stated consumption values are for guidance and depend on the nature of the substrate and the application method. Exact consumption values can only be determined by trials on the substrate.
Please Note
When using coloured mineral render, slight deviations in colour shade and irregularities can appear due to weathering which are a feature of the product. To minimise fluctuations in colour shades due to different batch numbers, the render requirement for one application should be ordered as one batch if possible.
Coating
KEIM Brillantputz Rauputz has to be coated with a single layer of KEIM Mineral Paint. Prior to coating observe a standing time of a minimum of 5 days.
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
• These colour samples are to be used for guidance only.
• Product contained within is generic to provide a close representation to your chosen colour.
• Should not be used to carry out any painting project, this is for colour selection purposes only and does not remove the need for you to ensure the correct product is chosen and tested for your application once a colour has been decided on.
• It is not a sample of the product you intend to purchase/use and cannot be used to test anything other than colour appearance.
• Notwithstanding any other provision of our conditions of sale, you agree and understand that many factors affect the colour of a painted product, including lighting, sheen level, method of application, batches variances number of coats and substrate surface.
• We cannot therefore promise that the colour of the product you ultimately purchase will exactly match the colour of this colour sample.
• Once you have selected a colour, you must purchase the smallest amount of the product you intend to use in your chosen colour and apply to a small, inconspicuous test area to be sure that it meets your expectations.
• Leave the product for 24 hours and then only buy more paint and/or apply more paint if you are completely happy with the results on the test area.
• We cannot be liable to you for any loss or damage if you have not complied with this process.
• Notwithstanding any other provision of our conditions of sale, you agree and understand that many factors affect the colour of a painted product, including lighting, sheen level, method of application and product surface.
• We cannot therefore promise that the colour of the product you paint with the Kolorbond paint will exactly match the colour of the item you send to us.
• You must therefore purchase the smallest Kolorbond paint pot available first and then apply the paint to a small, and where possible hidden, test area of your product to be sure that it meets your expectations.
• Leave the product for 24 hours and then only buy more paint and/or apply more paint to your product if you are completely happy with the results on the test area.
• We cannot be liable to you for any loss or damage if you have not complied with this process.