Fosroc Cemtop XD is a polymer modified, cement based, floor levelling compound.
For use as a heavy duty, highly abrasion resistant floor surfacing system. Suitable for industrial and commercial buildings, for new construction or refurbishment projects. Please also see the 'Uses' table in the Product Data Sheet.
Fosroc Cemtop GP is also available if a 'general use' product is required.
Cemtop products comply with classifications according to EN13813:2002 to EN13501-1:2007 - fire resistance classification as A1b.
Cemtop products and Nitoprime 33 are non-flammable. The fire resistance of Cemtop is classified as A1b according to EN13501-1:2007
Please refer to the Product Data Sheet for full details of:
Specification Clauses
Properties
Application Instructions
Uses
Physical Properties
Storage
Precaution
Additional Information
Application Notes
It is essential that both new and old concrete floors are correctly prepared prior to the application of Cemtop - See 'Surface Preparation' in the Product Data Sheet
Prime the surface with Fosroc Nitoprime 33 (1:5 primer to water ratio by volume) and allow to dry
Re-prime the surface with Fosroc Nitoprime 33 (1:3 primer to water ratio by volume) and allow to dry
Apply Cemtop to the required thickness onto the dry, primed surface
The objective of priming is to seal the substrate to prevent release of air from the substrate
Concrete slabs onto which the Cemtop is to be applied must have a surface temperature of at least +5°C with air temperature maintained at +10°C or more during application
For temperatures in excess of 25°C during application please contact our technical department on 0113 2455450 (option 2) or send a message to [email protected]
Protect from freezing for 48 hours after placement
To prevent rapid drying protect from direct sunlight and/or drying winds during application and the initial curing period
If the substrate onto which Cemtop is applied moves or cracks, reflective cracking may occur
Cemtop should not be applied to asphalt substrates
Cemtop should not be applied to external surfaces or surfaces subject to wetting
Joints:
Expansion joints in the existing substrate must be continued through the Cemtop products and filled to the required level with Fosroc Nitoseal MS300. The Cemtop system can be laid over construction joints or day joints. However, if these joints subsequently move, reflective cracking may occur
IMPORTANT FIRE PRODUCTS NOTICE: The information displayed on this website should be used as a guide ONLY and our Technical Department should be contactedto obtain a tailored specification and any advice necessary before you place an order for fire protection products. Fire protection products are non-returnable except in accordance with Condition 8 of the Terms and Conditionsand should be applied only by an individual with the necessary expertise and experience.We will not be held liable for any resulting damage to property, human life or monetary costs incurred due to the incorrect specification you have prepared or use of fire protection products caused by your negligence, including your failure to have contacted us to obtain the relevant advice/specification.
Product Details
7152-904404
Data sheet
Manufacturer
Fosroc
For Use By
Professional Use
Interior / Exterior Use
Interior Use
For Use On
Concrete
Sheen
N/A
Single, Two or Three Pack
Single
Pack Size
25kg
Application
Hand Pump
Coverage
1.7 kg/mm/m²
Shelf Life (from date of manufacture)
6 months - If stored at high temperatures and/or high humidity conditions the shelf life may be reduced to less than 3 months
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Fosroc Cemtop XD is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
Fosroc Cemtop GP is a polymer modified, cement based, floor levelling compound. Suitable for use as a general purpose self-levelling underlayment before the application of floor finishes such as tiles, carpet, vinyl or Fosroc Cemtop XD. Cemtop GP is also suitable as a floor finish for foot traffic or light commercial areas. Please also see...
Fosroc Nitoprime 33 is the recommended primer for the Fosroc Cemtop range of cementitious self-levelling floor toppings applied to concrete and cementitious substrates. It is a water-based primer which seals the substrate preventing the release of air by the concrete that could form bubbles in the flooring compound. In addition, it “wets” the...
Fosroc Nitoflor FC130 is a two-component water based epoxy resin floor coating system supplied in pre-weighed packs ready for on-site mixing and use. Suitable for use on concrete and asphalt substrates including walls and floors in warehouses, garages, light industrial and food processing areas, kitchens and other areas of pedestrian and...
Fosroc Nitoflor FC150 is a is a high performance, solvent free, epoxy resin coating system supplied in pre-weighed packs ready for onsite mixing and use. Suitable for use on concrete in production assembly areas, workshops, dairies, soft drinks production and bottling plants, breweries, kitchens, showrooms and internal car parks. It is...
Fosroc Nitoseal MS300 is a one part, high modulus, damp tolerant, floor and pavement joint sealant based on hybrid silyl modified polyether technology. Suitable for use for sealing saw-cut and movement joints in internal floors, and external joints where abrasion resistance is required. It can also be used for external facade joints where a...