AdSeal Imprinted Concrete Sealer is a hard wearing, high solids blend of UV stable MMA polymers suspended in aromatic hydrocarbons designed to seal and protect Pattern Imprinted Concrete (also known as ‘Stamped Concrete’), dries quickly to a tough, glossy finish. It protects, preserves, colours, hardens, enhances and can also be used on a wide range of other surfaces such as block paving, plain or exposed aggregate concrete surfaces, flags & slabs, etc. and will also stabilise jointing sand in between block paving.
AdSeal Imprinted Concrete Sealer is a colourless, non-yellowing, UV stable single component, low viscosity product with fast cure enabling rapid installation and early re-use of facility.
Increased impact and abrasion resistance maintains, and arguably increases, performance life of surfaces and can yield significant ‘whole life’ cost savings. Its unique formulation makes it easy to apply and achieve an even, uniform, and seamless finish.
Virtually eliminates grass and weed growth in any joints and reduces routine maintenance. A major feature is the combination of its hard wearing qualities with its ease of recoating/refreshing during future maintenance, unlike urethane based products.
Not suitable for: Engineering bricks, highly polished & glazed surfaces.
Performance (low to medium trafficked areas): With correct maintenance and depending upon surface type, potentially 10 years plus*. Externally colour will remain for 1 – 2 years although protective effect will remain for longer, potentially 4 – 6 years, depending upon surface type.
*A major design feature of this product is that it is easily re-coatable and does not need stripping before future treatment as maintenance coats cross link into original forming a monolithic layer. Recoating worn areas effectively means that the sealer may never need stripping and replacing.
Surfaces should be clean, dry & free from oil, grease, dust, laitance and any other deleterious materials
Do not apply in temperatures below +5°C or above +25°C and should not be subjected to extremes of temperature until completely dry
It is important to undertake a representative test area to ensure that the product is suitable for your requirements prior to commencement of the project and assessed for final appearance, chemical resistance and wet and dry slip resistance. This is particularly important where the surface has previously been sealed
Application should ideally be by an airless sprayer designed for solvent based products such as the AdSeal Compact Sprayer but application by brush or roller is also suitable [see detailed installation instructions]
During application care should be taken to protect adjacent areas & equipment from overspray
The surface should be sectioned off to assist accurate coverage
On average apply at a rate of approximately 4m² per litre for your first coat and 7m² per litre for the second. Exact consumption will depend on age and porosity of the surface
Apply in THIN uniform coats maintaining a wet edge but do not allow to puddle
Under normal conditions it will be touch dry within 1 - 2 hours and may be lightly trafficked after 24 hours
The above is to be read in conjunction with the detailed Installation Instructions Sheet and the current Safety Data Sheet available to download from DATA SHEETS tab above
Maintenance:
Sweep regularly to remove abrasive dirt and grit from surface and rinse down weekly using a mild detergent if required
Spills and marks should be wiped up as soon as possible and not allowed to dry on
Should signs of wear appear a maintenance coat can be applied. Clean and thoroughly dry surface to be treated. Apply single ‘tight' coat which will cross link into earlier coats, so there is no need to strip unless there is resin build up or blemishes are an issue
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
AdSeal Imprinted Concrete Sealer is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
AdSeal Surface Cleaner is a proven, industrial strength, yet gentle, degreasing solution that effectively cleans soiled surfaces and can be diluted with water depending on the strength needed. The Water-based formula provides an economical, effective cleaner that removes grease, oil, adhesive, floor polish, transmission fluid, release agent...
AdSeal Colour Pigment can be used to blend in faded or chipped areas by adding a small amount to AdSeal Imprinted Concrete Sealer. The amount added can be chosen to either add a subtle tint or to completely obscure.
Can also be used to colour plain concrete
Available in 6 standard colours
More Information Delivery Info
AdSeal Compact Sprayer is an ideal starter sprayer for the contractor or for the DIYer. Ordinary garden sprayer can't be used for resin as it clogs them and damages the seal irretrievably within minutes. AdSeal Compact Sprayer has 'Viton' seals and solvent resistant hoses which allow for use with resin products.
Gives excellent results and...
AdSeal Low-Slip Additive is designed to be mixed into AdSeal Imprinted Concrete Sealer. The additive is designed to be invisible when mixed correctly.
One pack of low slip additive per 25 litre can of sealer
Can be used for brush, roller or spray application using the AdSeal Compact Sprayer
More Information Delivery Info
