Ultraflex Waterproof Roof Coating is a high performance waterproofing system for use on new and existing roofs, walkways, balconies, gutters, etc, applying straight from the tin with a solvent-resistant roller, and drying in 2-8 hours (depending on the weather). Surfaces are fully trafficable once fully cured after 24 hours, with Ultraflex forming a seamless membrane on installation.
The coating system has excellent adhesion to a variety of substrates, including plywood, bitumen membranes, asphalt, metals, brick, concrete and wood, combining with Ultraflex Matting to ensure easy wet-on-wet application. Ultratop topcoat can be applied no later than 48 hours after Ultraflex for a glossy finish and extended guarantee - see the relevant product data sheets and application guides for more information or give our technical team a call on 0113 2455450.
Ultraflex Waterproof Roof Coating is BBA certified for life in excess of 25 years and has NHBC and Green Roof Approval.
15-25yr Guarantee - please see 'Guarantee Information' below for details.
Quick Links - Click To Jump To Section:
Features & Benefits
- Ready to use straight out of the tin - application with a solvent resistant roller
- Use on new or existing roofs, walkways, balconies, gutters etc
- Excellent adhesion to different substrates: plywood, bitumen membranes, asphalt, metals, brick, concrete, wood etc
- Fresh concrete must be cured for 28 days
- On EPDM and TPO it is recommended to install patch test to check compatibility
- Can be used all year round – moisture curing
- Use fully reinforced with Ultraflex matting to ensure easy ‘wet on wet’ application
- Instantly rain resistant once the matting is encapsulated
- Fully trafficable when cured
- Once installed, forms a seamless membrane
- 15-25yr Guarantee - please see 'Guarantee Information' below for details
- BBA certified for life in excess of 25 years
- NHBC and Green Roof Approval
- Do not use silicone sealants. Always use PU based mastics
Preparation
Stir before use.
Apply when ambient temperature is minimum of 2 degrees and rising and not exceeding 30°C.
Ensure substrate is in good condition, dry, clean and free from dust, moss or lichen.
All edge trims to be fixed to substrate prior to application of Ultraflex.
Ultraflex is self-terminating, if brickwork is in good condition, strike a line using tape on the brickwork to coat up to (important: when the Ultraflex has been installed ensure the tape is pulled before the Ultraflex is dry). If the brickwork is in poor condition a termination bar or flashing is required.
Application
Open tin and mix thoroughly before using.
Apply Ultraflex straight out of the can onto the substrate using a solvent resistant roller. Dry roll Ultraflex Matting into the product until the Ultraflex is drawn through, then immediately apply another coat of Ultraflex ensuring the matting is fully embedded avoiding any pinholes.
It is advised to start at the perimeter of the area including upstands to a minimum of 150mm (if possible), ensuring the matting overlaps any trims (including fixings) / joints / change of material by 50mm.
Infill the remaining field area using the same method as above using Ultraflex matting, at a minimum coverage rate of 1.5kg per m². The whole area including trims must be coated to form a continuous seamless membrane. Please take time to make sure no pin holes exist.
Optional: Apply an optional layer of Ultratop topcoat for glossy finish and extended guarantee once the ultraflex is fully cured and no later than 48 hours after Ultraflex application.
Please the the 'Data Sheets' tab for detailed application guides.
Drying Times
Drying time will be approx. 2-8 hours depending on weather, fully cured in 24 hours.
Guarantee Information
- 15 Year Guarantee - Minimum 1.5kg/m² of Eagle Ultraflex Waterproof Roof Coating fully reinforced with Eagle Ultraflex Matting and finished with Eagle Ultratop Topcoat at 150g/m² once the Ultraflex has cured (minimum 24 hours)
- 20 Year Guarantee – As above but the contractor must be trained on the product (contact us for details, costs associated for training)
- 25 Year Guarantee - Minimum 2kg/m² of Eagle Ultraflex Waterproof Roof Coating made up of the following:
- Initial application 1.5kg/m² fully reinforced with Eagle Ultraflex Matting
- Additional coat of Ultraflex (without matting) 0.5kg/m² after the initial application has cured (minimum 24 hours)
- Final coat of Eagle Ultratop Topcoat at 150g/m² to finish once the second application of Ultraflex has cured (minimum 24 hours)
- Contractor must be trained on the product
- In all cases the customer must register the job to get the guarantee using the ‘Guarantee Requisition’ form available to download HERE
- Once complete, the form should be sent to [email protected]