Fosroc Brushbond FLXIII is a two component, cementitious, polymer modified elastomeric waterproofing coating for concrete surfaces.
Suitable for use on buried structures such as bridge abutments, culverts and retaining walls. Also for use on reinforced concrete roof decks, in conjunction with protective finishes.
Brushbond FLXIII complies with EN1504-2: Surface protection systems method 1.3 (Ingress Protection), 2.2 (Moisture Control), 5.1 (Physical Resistance) and 8.2 (Increasing Resistivity).
Please note: Colours shown are for illustrative purposes only. Black is available as POA only please contact our Technical Department on 0113 2455450(option 2) or send a message to[email protected] for details.
Suitable for light foot traffic prior to installation of protective finishes
Designed to be easily mixed on-site using a slow speed drill and paddle and then applied to the substrate using a brush, roller or by spray application
Available in grey and black, cures to form an elastomeric, waterproof coating
CE Marked and complies with EN1504-2 surface protection systems methods 1.3, 2.2, 5.1 and 8.2
Brushbond FLX III should be applied over a 20mm Fosroc Renderoc Plug 20 fillet and Fosroc Proofex LM Mesh embedded as described in the Product Data Sheet. Proofex Overtape may be used at corner intersections
Sealed Joints:
Soft joints that are to remain exposed should be filled with a suitable joint sealant such as Fosroc Nitoseal MS600 after application of Brushbond FLX III which should be returned into the joint faces
For static joints apply 100mm wide Fosroc Proofex Overtape centrally placed over the joint and extend the Brushbond FLX III application over the joint
For movement joints apply Fosroc Brushbond FLX III up to the joint face. When cured apply Fosroc Expoband H45 over the sealed joint (see data sheet) and allow to cure. Finally lap additional Brushbond FLX III onto the cured Fosroc Supastik E10
Topcoat for Exposed Surfaces:
For surfaces exposed to UV light in service, a minimum 0.2mm film of Fosroc Nitoproof UVR Topcoat of the appropriate colour should be applied. See product data sheet for application instructions
Limitations
Brushbond FLXIII should not be applied if the air or substrate temperature is greater than 40°C. This may result in different colour shades
Minimum application, substrate and air temperature is 3°C and rising
Avoid freezing conditions for 24 hours after application
Product Details
7130-904293
Data sheet
Manufacturer
Fosroc
For Use By
Professional Use
For Use On
Concrete
Sheen
N/A
Single, Two or Three Pack
Two-Pack
Pack Size
25KG
Application
Brush, Roller, Spray
Coverage
14.5m²/pack applied at 1mm thick (2 coats of 500 microns thick)
Shelf Life (from date of manufacture)
12 months If stored at high temperature/humidity, the shelf life may be reduced to less than 6 months
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Fosroc Brushbond FLXIII is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
Fosroc Nitoseal MS600 is a one part, engineering sealant for immersed conditions based on hybrid silyl modified polyether technology. Suitable for use for sealing movement joints in buildings and civil engineering structures including joints that will be subject to intermittent or permanent immersion. Typical applications include - Potable...
We no longer stock this product, but can recommend Fosroc Expoband H100 as a great alternative. Please note: it is important to check that any alternative product is suitable for your requirements, as our suggestion is given in good faith but without warranty. If you are in any doubt please first contact our technical team on 0113 2455450...
Fosroc Supastik E10 Adhesive is a two-pack epoxy adhesive for use on concrete. Suitable for use as an adhesive with selected Fosroc products including Fosroc Expoband H45. Please see the Product Data Sheet for the relevant base product for application and mixing details for Supastik E10 Adhesive. More Information Delivery Info
Fosroc Ancillaries are a range of application tools and accessories for use when applying Fosroc products. Range Includes:Fosroc Sealant Mixing Paddle, Fosroc Thioflex Follower Plate, Fosroc Polyurea Accessories Please see below for detailed information and order references where applicableMore Information Delivery Info
Fosroc Renderoc Plug 20 is a rapid setting cement-based, water-stopping mortar which is easy to apply to horizontal, vertical or overhead surfaces at a wide range of thicknesses, conforming to the requirements of BS EN 1504 Class R1. For the rapid patching and plugging of concrete segments, concrete and brick tunnel linings, sewage systems,...
Fosroc Proofex LM is a two component bituminous rubber emulsion with special hydraulically hardening fillers for waterproofing of underground structures and intricate details e.g. pipe entries, covings etc. Tested in accordance with DIN 18195, parts 4 to 6. General test certificate No. P-22 1356 8 96-1, MPA Dortmund. Ideal for use in...
Fosroc Proofex Cavitydrain Accessories are a range of accessories for use when applying Proofex Cavitydrain products as part of a Fosroc Proofex Waterproofing System. Range includes:Brick, plaster and fixing plugs & seals, sealing tapes Drainage channels and channel piecesPlease see below for detailed information and order...
A two component, high solids, flexible, light to medium-duty trafficable, colour stable and flame retardant polyurethane coating. Part of - and fire rated to - BS476-3:EXT.F.AA when used in conjunction with:Fosroc Nitoproof 800 roof/balcony waterproofing system Fosroc Polyurea WPE waterproofing systemLEED SS10 v4.1 passPlease...