Rust-Oleum Thinner 22 is for the dilution of synthetic enamels and varnishes for airless application. Degreasing of metals and most wood types. Cleaning of 'spots' of acrylic paints and acrylic fixing paints (e.g. on glass). Best used to dilute the following products: Primer 44 Fassiclor Galvaprim Vernac Gloss Vernac Satin
Rust-Oleum Fillcoat Fibres Repair Kit
Rust-Oleum Fillcoat Fibres Repair Kit is a complete kit that seals leaks quickly and simply, even in bad weather!
- Thick waterproofing roof repair paint
- For use in any weather (even in the wet)
- Adheres to wet surfaces
- Fibres reinforced
- Crack bridging (2mm) - 1300% elastic
- Recommended for use on leaking flat or pitched roofs, guttering, ridge pieces, chimney stacks, roof tiles, glass, and more (see the product datasheet)
- Emergency Leaking Roof Repair Kit includes 1 litre of Dark Grey Rust-Oleum Mathys Fillcoat Fibres, instruction sheet, brush, gloves, stirring stick, sanding pad, crack bridging fleece
Rust-Oleum Fillcoat Fibres Repair Kit is a repair compound for flat and pitched roofs. It is instantly waterproofing and remains up to 1300% elastic, providing good resistance against weather influences, mineral acids (max. 10% in water) and does not contain bituminous products.
- Leaking roofs
- Ridge pieces
- Chimney stacks
- Non-walkable terraces
- Hard PVC
Rust-Oleum Fillcoat Fibres Repair Kit has excellent adhesion on different substrates and after cleaning, can be applied directly on bituminous substrates.
Porous materials (concrete, stone, wood) must first be dried and pre-treated with a coat of Rust-Oleum Mathys Primer 44 HS.
Easy to use emergency kit includes:
1 litre of Dark Grey
Remove dust, mud, grease, moss and withered leaves carefully. The spots to be repaired are cleaned with a hard broom and sponged. After cleaning, Rust-Oleum Fillcoat Fibres Repair Kit can be applied directly on bituminous substrates, hard PVC, polyester, zinc, aluminium, glass, tiles, etc. Porous materials (concrete, stone, wood) must first be dried and pre-treated with a coat of Rust-Oleum Mathys Primer 44 HS. In case of repeatedly repaired spots, important or active cracks, apply Rust-Oleum Fillcoat Fibres Repair Kit crosswise over the cracks or fissures. Consumption: 1,5 kg/m² with a hawk or a block brush.
Directions for Use
To ensure homogeneity, coating materials should be thoroughly stirred prior to use.
Application & Thinning
- Brush: Do not dilute.
- Roller: Not recommended.
- Air-atomised spray: Not recommended.
- Airless spray: Not recommended.
- Cleanup: Rust-Oleum Thinner 22 or White Spirit.
Can be applied during all weather conditions, except for snow.
- Use an adhesion primer on Rust-Oleum Mathys Dac Hydro Alu.
- Product is recoatable with Rust-Oleum Mathys Dacfill Waterproofing, Rust-Oleum Mathys Coating PRT or Rust-Oleum Mathys Dac Hydro Alu.
- Never apply Rust-Oleum Fillcoat Fibres Repair Kit to polystyrene insulation or onto new concrete (concrete should be at least 2 years old).
- Do not apply Rust-Oleum Fillcoat Fibres Repair Kit as priming coat under Rust-Oleum Mathys Dac Hydro Alu.
- When using Rust-Oleum Fillcoat Fibres Repair Kit, smooth out the product in one direction, preferably perpendicularly to the cracks.
Please contact Rawlins Paints' Technical Support Team on 0113 2455450 for more information.
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
- Dry to Recoat (at 20°C)
- 3 - 14 days with the same product. 6 weeks with a paint
- 1m² per kit
- Solids by Volume
- 43 %
- 485 g/l
- Shelf Life (from date of manufacture)
- 5 years from date of production in unopened cans, if stored in dry, well ventilated areas, not in direct sunlight at temperatures between 5° and 35°C.
- Touch Dry
- 2 hours (waterproof instantly)
- UN Number
- Not regulated
- 1 coat of 1,5 l/m²
|Roland on 11/07/2019|| |
Can this product be used on flat roof covered with rubber lining materials
No, we would instead recommend Gaco Liquid Roof Tape.
|Sam Dorrian on 04/06/2019|| |
Can this product be used to seal a failed lead box gutter? The product specification references zinc but not lead. Thanks
Yes, this product after cleaning and preparation can be applied to lead and is ideal in gutters.
|colin stewart on 06/05/2019|| |
Can this product be used to seal cracks in corrugated Asbestos roofing AND from the INSIDE ??
This product would be for use on the exterior (top side) of the roof only and the surface (after cleaning in accorandce with local regulations) would first need to be primed with Rust-Oleum Mathys Primer 44 HS. If you the wished to encapsulate the interior, underside of the roof to seal isolated asbestos fibres and prevent release you could use Thermoguard Asbestos Encapsulating Coating.
|Debra on 10/07/2018|| |
Can I use this product on concrete gutters to seal them
Yes, however porous materials (concrete, stone, wood) must first be dried and pre-treated with a coat of Rust-Oleum Mathys Primer 44 HS.
|trevor on 25/06/2018|| |
can i use rust-oleum fibre kit on my corrugated steel roof to repair a leak and how long would it likely last
Yes, Rust-Oleum Fillcoat Fibres Repair Kit may be used for this purpose, obviously depending on the actual source of the leak, and how large the “damaged” area is will determine the effectiveness of this. In terms of longevity we would estimate approximately five years, but this would require the steel to be thoroughly de-rusted first of all.
|m jones on 12/06/2018|| |
Good Morning .... I have a slate water feature in my garden and the water compartment has sprung a leak .... would Rust-Oleum Fillcoat Fibre Repair kit solve the problem and if so can I paint it onto the inside of the tank? Thank you.
We would suggest that the Fillcoat Fibres could offer a short term solution for this issue. However, we are presuming there has been some kind of structural failure (hence “springing a leak”) and without knowing more about that, we cannot advise how effective the Fillcoat Fibres will be, or for how long.
|Craig Bell on 03/02/2018|| |
Rust-Oleum Fillcoat Fibres Repair Kit. Can this be used to repair flat fibreglass roof? Thanks
Rust-Oleum Mathys Dacfill Waterproofing is a watertight, water-based liquid membrane for roofs: Forms a lasting elastic coat without joints or seams on sloping roofs (min. 5% slope) Has been tested and independently approved for asbestos encapsulation which makes it an excellent alternative to asbestos sheet replacement saving cost, time...
Rust-Oleum Mathys Dac Hydro Alu is a waterborne, ready-to-use aluminium coating for decoration, heat reflection and lasting protection of metal and most bituminous roofs. It has excellent resistance to extreme weather and temperature fluctuations. 400% elastic, water vapour permeable it builds an abrasion resistant, rubberlike coat without...
Rust-Oleum Mathys Primer 44 HS has a large fixation capacity for stabilising loose particles and improving the adherence of subsequent topcoats. Features and Benefits Unsaponifiable Good UV resistance Excellent fixation on roofs Very flexible Chlorinated rubber technology, solvent-based Quickly water-resistant (1 hour after...
Rust-Oleum Mathys Coating PRT is ideal as a topcoat on Rust-Oleum Mathys Dacfill Waterproofing for improved resistance to continuous water immersion or on Rust-Oleum Mathys Noxyde to minimise dirt retention Flexible durable paint for renovation of roofs, ideal for making roofs white Resistant to UV, acid rain, heat, frost and pollution...
A high build coat that is ideal for carrying out repairs to flat roofs, pitched roofs and gutters. Top Features Approx coverage: 2.5-5m² Normally dires in 2-3 days Available in grey, white or black
Specially-formulated for emergency roof repairs no matter how bad the weather; can even be applied under water. Ideal for roofs which need immediate repair to stop leaks. Advantages Suitable for all building materials External use only Can be applied in falling rain
Rust-Oleum LeakSeal is an easy-to-use, rubberised protective utility coating designed to fill and seal leaks and cracks. Features and Benefits Seals leaks and cracks water-tight Paintable finish Anti-rust/corrosion Will not sag/drip Can be topcoated after 24hrs Now available in: Clear Aluminium White
Because of the high level of fibre re-enforcement small cracks only require one brush coat application to give instant and total water protection, even in areas subject to ponding - requires no primer on sound non-porous surfaces.
Everbuild 905 All Weather Roof Coating is a solvent based, full bodied black brushable compound with added fibres for reinforcement. It is specifically designed for overcoating leaking roofs. Dries to a tough black coating.
Use Eagle Aquapol Acrylic Roof Coating for emergency repairs and routine maintenance on most surface types on failed industrial and domestic roofs. The coating is instantly waterproof after a single coat, applying even in damp conditions, remaining flexible with exceptional weather resistance. Instant roof repair for most roof types:...
Rust-Oleum Mathys Fillcoat Fibres is an emergency repair, instantly waterproofing, fibre reinforced coating for flat and pitched roofs to seal leaks and cracks quickly and simply, even in bad weather: Direct repair of roofs, non-walkable terraces, gutters, ridge-pieces, chimney stacks, pipes, etc. Excellent adhesion directly to bituminous...
Using advanced polyurethane technology, felt, asphalt, GRP, lead, timber, concrete, and much more can be coated with Bullet Ready Roof “liquid rubber” to seamlessly waterproof and protect for years to come. Top Features Up to 5m² per kit Fully Refurbish or Repair Easy to apply in just ONE thick coat (instructions provided) The permanent...
GacoPatch is a flashing grade, standalone roof patch made with 100% silicone. ADVANTAGES New, improved technology One-step application limits costs Permanently flexible UV stable Will not chalk, crack or peel Vertical or horizontal application
Bonds, seals and fills almost anything without a primer, even when wet or fully submerged. This unique hybrid polymer formulation contains no solvents. Top Features Premium quality high modulus sealant. Neutral system, free from isocyanates and silicones. Non staining, odour free and bubble free curing. Good movement...