Everbuild Evercryl One Coat

Manufacturer:

Because of the high level of fibre re-enforcement small cracks only require one brush coat application to give instant and total water protection, even in areas subject to ponding - requires no primer on sound non-porous surfaces.

Bulk Buy

£191.68 tax excl.

£230.02   tax incl.
Available colours:

Product Description

Everbuild Evercryl One Coat is a resin based, fibre re-enforced roof repair compound which is effective on all common flat and pitched roofing surfaces and types, giving an instant roof repair even in the wet and on wet surfaces. May also be applied in frosty conditions down to –5°C. Everbuild Evercryl One Coat is instantly waterproof when applied, so there is no fear of wash off, so emergency leaks can be tackled immediately as there is no need to wait for the rain to stop. Everbuild Evercryl One Coat is brush applied and dries to a smooth seamless flexible membrane which resists algae and fungal growth. Because of the high level of fibre re-enforcement, Everbuild Evercryl One Coat will bridge small cracks and requires only a one-coat brush application to give instant and total water protection, even in areas subject to ponding. Everbuild Evercryl One Coat requires no primer on sound non-porous surfaces.

Benefits

  • May be applied in damp and wet conditions.
  • Formulated from lightfast acrylic polymers to withstand sunlight for longer periods than traditional bitumen coatings
  • Fibre re-enforced to bridge small cracks.
  • Primerless adhesion to most bituminous and non porous surfaces.

 Areas For Use

  • General sealing, maintenance, repair and waterproofing of most common roofs in wet or dry conditions– for use on concrete, fibre/cement, roofing felt, mastic asphalt, existing bituminous roof coatings, rigid uPVC corrugated iron, metals, slates, brickwork, tiles, lead, copper and zinc.
  • Waterproofing guttering (plastic and metal), downpipes, gully’s, flashings, upstands, vents and leadwork.

Limitations

Do not use in areas where subsequent solvent or oil contact is likely. Avoid inhalation of vapours. Do not use on Styrofoam or PVC foil. As the manufacturer cannot know all the uses its products may be put to, it is the users responsibility to determine suitability for use. If in doubt, contact technical services department for advice.

It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.

Technical Data

Typical Coverage (per coat)0.5-1m² per litre
Touch DryInstantly rain resistant
ApplicationBrush
The figures stated above are approximate. Please ensure you refer to all datasheets for full application information.

Download

Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

Questions



questions mr Bagott on 15/03/2018
Question: 

Do you have a roofing product that will fill and seal the ponding on a bitumen flat roof,? I may not be able to dry it out fully Thank you

Answer: 

Rust-Oleum Fillcoat and Rust-Oleum Fillcoat Fibres can be applied even in bad weather and surfaces do not have to be completely dry before application. Neither however can 'build up' the roof surface to infill depressions, the roof surface must be repaired before application.

questions Tom waddington on 07/07/2015
Question: 

I have got a leaking fibreglass roof, what is the best paint to put on it to stop it from leaking?

Answer: 

We would recommend Rust-Oleum Mathys Fillcoat Fibres. It is an instantly waterproof, fibre reinforced repair coating for roofs to seal leaks and cracks up to 2mm wide, quickly and simply, even on fibreglass.


Question about the product

* Required fields
Send

The question has been correctly sent

Free delivery

On orders over
£75.00 + VAT

Low trade prices

Our best trade prices on everything!

Technical Advice

Fast FREE Technical Advice for Products & Projects

Click & collect

Order and collect from
our Leeds based trade store.
silent-exothermic unable