GacoFlex SF2036 WalkPad



GacoFlex SF2036 WalkPad is a stay-put solution for creating highly-visible rooftop walkways. It is an exceptionally durable, silicone-based, solvent-free coating that is combined with a reinforcing agent to provide exceptional durability and resistance to traffic and tears.

Bulk Buy

£397.00 tax excl.

£476.40   tax incl.

Product Description

GacoFlex SF2036 WalkPad is a silicone-based, solvent-free, single-component waterproof elastomeric moisture-curing sealant combined with a reinforcing agent and is specifically formulated for exceptional durability.

GacoFlex SF2036 WalkPad is intended for application over GacoFlex Silicone Coatings and a variety of other roofing substrates to create a rooftop walkway for pedestrian maintenance traffic. Unlike conventional mats, WalkPad becomes an integral part of the roof. The yellow color provides a highly visible and aesthetic rooftop walkway, and when combined with GacoFlex WalkPad Granules will offer traction and resistance to wear under light foot traffic.

Adhesion is excellent when applied directly over GacoFlex Silicone Coatings. A primer may be required for adhesion to other surfaces including built-up roofing, modified bitumen capsheet, single ply roofing (EPDM, TPO, PVC and Hypalon®), masonry, concrete, and wood. A primer must be used on all ferrous metals to prevent corrosion. Contact the Technical Department for specific recommendations.

No primer is needed when WalkPad is being applied directly over GacoFlex Silicone Coatings. If applying WalkPad to any other surface, apply GacoFlex E5320 2-Part Epoxy Primer/Filler according to label directions.

Apply by brush or trowel as received. Apply WalkPad at a rate of 4 gallons per 100 sq. ft.

When using WalkPad to create a rooftop walkway for pedestrian maintenance traffic, it is recommended that GacoFlex WalkPad Granules be applied to the wet product at a rate of 0.5 lb. per 100 sq.ft. to help ensure good traction. CAUTION: While the use of granules will improve traction, caution should still be exercised when walking on WalkPad, especially in wet conditions.

NOTE: Application rate is job-specific. Additional material may be required due to surface profile, losses due to overspray and wind, and residual coating left in the container.

Allow to dry a minimum of 4 hours at 55°F (13°C) or higher, or until it can be safely walked on (product is moisture cure, low humidity will result in longer dry times).

It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.

Technical Data

Typical Coverage (per coat)0.6m² per litre
Touch Dry4 Hours
The figures stated above are approximate. Please ensure you refer to all datasheets for full application information.


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!

Question about the product

* Required fields

The question has been correctly sent

Free delivery

On orders over
£75.00 + VAT

Low trade prices

Our best trade prices on everything!

Technical Advice

Fast FREE Technical Advice for Products & Projects

Click & collect

Order and collect from
our Leeds based trade store.
silent-exothermic unable