Please note that Black & Solar Reflective White are subject to a minimum order quantity of 360kg in any pack size derivative.
Britannia Aquashield Aggregated Coating is a one-pack solvent-based aggregated coating for safety on high level walkways and gutters. It is ready for use on flat roofs, pitched roofs, high level walkways, weathered asphalt and bituminous surfaces, gutters, concrete, brickwork, GRP and fibreglass, felt and metal (galvanised and ferrous).
It waterproofs the substrate instantly and rainfall immediately after application has no adverse effect.
Not for use on balconies, timber surfaces, new and aged PVC, plasticised PVC (Plastisol) or internal use.
Ready for use on flat roofs, pitched roofs, high level walkways, weathered asphalt and bituminous surfaces, gutters, concrete, brickwork, GRP and fibreglass, felt and metal (galvanised and ferrous)
Rainfall immediately after application has no adverse effect
Particularly suitable for general maintenance work
Can be brush or roller applied
Good curing performance at low temperatures
Non-flammable
Application by brush or solvent resistant roller
External use only
Spreading Rate
These will vary depending on substrate, the site conditions and longevity required.
Typically spreading rates will vary depending on the end use.
High Build Coat: between 1kg - 2kg per square metre dependent on substrate
Applied as a topcoat approximately 1kg per square metre dependent on substrate
Drying Times
Up to 4-7 days depending on temperature, thickness of coating
The product may remain slightly soft for a further period depending on climatic conditions, this is not detrimental to the waterproofing qualities of the product
Preparation
Clear all areas of moss, lichen and debris by brushing or power washing and remove surface water and any contamination such as oil or grease and allow to dry. Apply Britannia Fungicidal Wash to prevent further fungal/algal growth.
Most roofing substrates to be treated will not normally require priming.
Highly Porous/Friable Surfaces:
Concrete, Concrete and Asbestos Cladding, Sheeting and Guttering should be primed with Britannia Aquashield Primer (see separate technical sheet) prior to over coating with Britannia Aquashield Aggregated Waterproof Roof Coating
All these areas should be suitably prepared and primed as appropriate (see separate technical sheet) before application of Britannia Aquashield Aggregated Waterproof Roof Coating
Non-Porous Substrates:
Slate, Polished bricks should be power washed abraded and completely dry, free from any contamination to achieve adhesion of the Britannia Aquashield Aggregated Waterproof Roof Coating
Bitumen Surfaces:
Discolouration may occur over a new asphalt, tar or bitumen surface; therefore an extra coat may be required, for decorative purposes only
Aged bitumen can be liable to crack, therefore further advice must be taken
Previously Painted or Coated Substrates:
It is good practice to inspect and carry out adhesion tests prior on any existing coating or substrate prior to application of the coating
Splits, Cracks, Joints and Seals:
Pay particular attention to clean out any splits/cracks/joints and seals by scraping or brushing off with a stiff bristle brush before applying the Britannia Aquashield Primer
Repair all faults in the surface by either Britannia’s Reinforcing Scrim in the first of two coats or using a proprietary sealer
Crazed Areas:
These should be primed with Britannia Aquashield Primer prior to the application of a coat of Britannia Aquashield Aggregated Waterproof Roof Coating
In areas where excessive movement may occur additional reinforcement must be incorporated into the coating.
Application
To the dry and cleaned surface, apply a generous coat of Britannia Aquashield Aggregated Waterproof Roof Coating by brush, roller or squeegee, at the minimum specified spreading rate as stated above under the heading
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Britannia Aquashield Aggregated Coating is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
Britannia Aquashield Primer is a solvent based primer for very porous and loose/friable surfaces. It ensures the Aquashield topcoat delivers optimum waterproofing performance.
Works instantly
Vital stabilisation of highly friable/porous surfaces
Rainfall immediately after application has no adverse effect
Can be brush, roller or spray...
Britannia Fungicidal Wash Solution is a water-based solution which controls and treats fungal and algal growth prior to painting external hard services.
Water based - Easy, quick and safe to use
Powerful, proven water based solution for external hard surfaces
Specially prepared fungicide controls and treats fungal and algal growth prior...
Britannia Reinforcing Scrim is a polyester-based mesh that can be used to reinforce the following: roof fixings, cracks, splits, holes and joints in asbestos gutters and sheeting, rooflights, metal, bituminous felts/coatings and asphalt surfaces, felted surfaces, single ply and fibreglass roofs and wood.
Used as a reinforcement with...