Teamac Acrylic Roof Coating - Special Colours


Teamac Acrylic Roof Coating - Special Colours, is a cost-effective product to protect, refresh and decorate surfaces and substrates:

  • Available in over 2,600+ colours from RAL, BS, NCS and the new NCS 2050 colours subject to a minimum order quantity of 4 x 5L and an extended lead time of 10-14 working days
  • For the range of readily-available standard colours please see Teamac Acrylic Roof Coating
  • Ideal for:
    • Tile and brick roofs
    • Sealing asbestos sheets
    • Corrugated asbestos roofs on agricultural buildings and barns
    • General areas (not floors) of masonry, wood, rendering and plasterwork

Product customisation

Don't forget to save your customization to be able to add to cart
  • 250 char. max
Colour Group
£108.41(ex. VAT)
£130.09 (inc. VAT)
Please choose your colour
Available for Delivery (See Delivery Options Below)

The minimum purchase order quantity for the product is 4.


Teamac Acrylic Roof Coating, is a fast drying, water based coating that dries to a low sheen finish.  It's a cost-effective product to protect, refresh and decorate tile and brick roofs as well as sealing asbestos sheets and barns.

Click To Jump To Section:

Features & Benefits

Suitable to be used on:

  • Tile and brick roofs.
  • Sealing asbestos sheets.
  • Corrugated asbestos roofs on agricultural buildings and barns.
  • General areas (not floors) of masonry, wood, rendering and plasterwork.
  • Red, grey, or green low sheen finish on asbestos sheets, brick roofs, and roof tiles.

Product Specification

Technical Data
Volume Solids 31 to 37%
VOC Content 41 max g/litre
SG 1.15 to 1.28 @ 20°C
Viscostity 3.0 Poise @ 25°C
Flash Point Non-flammable

Film Thickness Range And Coverage

Product Data
  Dry Film Thickness Wet Film Thickness Theoretical Coverage
Maximum 30 μm 85 μm 7 to 12 m²/litre @ 35 microns D.F.T depending on porosity.

The practical spreading rate may be lower as this depends on factors such as the porosity and roughness of the surface to be painted and material losses during application.

Drying Times

Drying Times At 20°C/RH 50%
Touch Dry: 2 Hours
Dry To Handle: 12 Hours
Dry To Recoat: 12 hours or overnight
Fully Cured: 3 - 5 Days

Low temperature and high humidity will adversely affect application, drying and performance of any coating.

Surface Preparation

  • Ensure all surfaces are clean, dry and free from grease, oil and any other contaminates.

Preceeding Coat

  • N/A


  • Mix well before use.

Application Conditions

  • Do not apply below 10°C.  Cold and damp conditions will prolong drying times.
  • As dictated by normal good painting practice.
  • In confined spaces, provide adequate ventilation during application and drying.

Application Methods

Method Airless Spray Conventional Spray Brush Roller
  No No Yes Yes

  • Thinner (Max vol): Clean Water (10%)
  • Nozzle Size: N/A
  • Nozzle Pressure: N/A
  • Cleaning Solvent: Clean Water

Health & Safety

See safety data sheet - SDS 10642 in attatchments section above.

Click to go back to the top of the page

Product Details

Data sheet

Fully Tintable
Suitable Substrates
Masonry, Render, Plaster
Dry to Handle (at 20°C)
12 Hours
Dry to Recoat (at 20°C)
12 hours or overnight
Fully Cured (at 20°C)
3 - 5 Days
7 to 12 m²/litre
Min. Application Temperature
Solids by Volume
31 to 37%
41 max g/litre
Touch Dry
2 Hours
5 litre
Recommended Dry Film Thickness
30 μm
Recommended Wet Film Thickness
85 μm
UN Number
Not regulated

Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

questions john lappin on 2023-04-19 19:44:29

Can this product be applied to old slate roof tiles?

Answer from Rawlins’ Technical Team: 

Unfortunately no this is not suitable for application to slate tiles.

Question about the product

* Required fields


Teamac Acrylic Roof Coating - Special Colours is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

All delivery costs below are excluding VAT

You might also like

General Painting Application Kit

General Painting Application Kit from Rawlins Paints provides the basics for any painting project. Whether it is a one off job, or you just want to make sure the right application tools get to site. Provides an economical way of making sure you will have what you need Ideal for interior and exterior paint projects Click to jump down to...

Price £8.02 (ex. VAT)
In Stock and Available for Delivery