Alternatively you can email our sales & support team on [email protected]
Tor Elastamat HD
SS6000225
Tor Elastamat HD (SS6000225) is a random weave chopped strand glass fibre mat for high strength reinforcement of Tor liquid applied roof waterproofing systems. It is used as a full reinforcement on heavy duty flat roof applications and where ponding is evident, and as localised or partial reinforcement in other areas.
Tor Elastamat HD (SS6000225) is a random weave chopped strand glass fibre mat for high strength reinforcement of Tor liquid applied roof waterproofing systems. It is used as a full reinforcement on heavy duty flat roof applications and where ponding is evident, and as localised or partial reinforcement in other areas. It helps to provide the ideal solution for areas subject to movement and damage, especially around vulnerable areas such as upstands, joints, etc.
The random nature of the weave allows the fibres to be easily incorporated within the roof coating and be moulded easily to rough and irregular surfaces. When encapsulated, the fibres help provide greater tensile strength and tear resistance to the roof coating system, whilst retaining its inherent flexibility.
Preparation & Application
Localised Reinforcement: Side laps, hairline and associated cracks, bolt heads, joints, movement joints, stepped joints and dissimilar adjoining substrates: Apply 1 coat of the roof coating to a minimum width of 75mm either side of the item. Whilst wet insert Tor Elastamat HD and thoroughly “wet-in”.
Upstands, detailing, protrusions, etc: Apply 1 coat of the roof coating to a minimum width of 150mm. Whilst wet insert Tor Elastamat HD and thoroughly “wet-in”.
Full Reinforcement: Apply 1 coat of the embedment coating at the prescribed coverage rate. Whilst wet insert Tor Elastamat HD and thoroughly “wet-in”. Overlap adjacent reinforcement areas already laid by at least 50mm ensuring sufficient extra embedment material is applied to these areas.
When embedding Tor Elastamat HD it may be necessary to tamp the mat. If so, use a short bristled brush or specialist roller ensuring that there are no tented areas. Immediately after embedding check for any upstanding glass fibre strands and lay smooth.
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Tor Elastascrim FT (SS6000140) is a non-flammable, semi-elastic, putty-like butyl rubber based strip encapsulant/sealant. Supplied in roll form on siliconised paper release backing for use as a formable pre-coat encapsulant and sealant over roof sheet bolts etc. Also usable as a lap joint gap filler/sealer on sheeted (profile metal, fibre-cement etc)...
Bullet Roof GRP Roofing Resin is a high grade GRP resin that is not reblended, which allows for the purity Bullet Roof GRP Resin.
Top Features
Medium reactivity ortho
Thixotropic
Pre-accelerated
Reduced styrene emission
GacoFlex SF2000 SeamSeal is a silicone-based, solvent-free, single-component waterproof elastomeric moisture-curing sealant combined with a reinforcing agent. Intended for application over cleaned and primed roofs as a joint and fastener treatment in place of fabric and/or elastomeric sheet tape. It may also be used to repair blisters in spray...
Tor Non-Taint Bitumen Primer (IM902) is a general purpose bituminous paint that can be used for steelwork, haysheds on farms etc. Also used for promoting adhesion of TorVap VCL / CM on Elastatherm TF square edged insulation, porous surfaces or in all cases where temperature is below 5°C.
A reinforcement fleece for the first coat of Murfill Waterproofing Coating on structural surfaces where required. When fleece is introduced it offers maximum durability, flexibility and strength to the system.
Eagle Non Drip Edge Trim for restricting water runoff in domestic and industrial applications.
Part of the Eagle range of roof trims.
Please refer to the image for dimensions.
Eagle Tecnoplastic Rubber Granules is a plastic bead, applied to a fully cured roof to provide a less harsh, non-slip surface for trafficked areas.
Good for barefoot traffic areas
Use with Tecnotop 2C
Available as a 2Kg tub, covering up to 100M2 (depending on density of the mixture)
A specially-formulated primer for application on to metals to enhance adhesion properties, and allow the primer to physically bond onto the metal using an incorporated activating acid that "etches" into the substrate.
Advantages
For Aluminium, Copper and Galvanised Steel surfaces.
White in colour.
Upto 12-months shelf life.
Rust-Oleum Mathys Dacfill / Dacfill HZ Fleece is a polyester woven mesh, flexible and elastic which is specified for use as a system with Dacfill HZ flat-roof coating. Reinforcement fleeces provide added durability, flexibility and strength to flat-roofs.
Sika MultiSeal is a self-adhesive sealing tape made from bitumen rubber compound, protected by a reinforced aluminium film. Use for general repair to existing flashing, roofs including sheet metal work, facades, broken roof tiles, leaking gutters, duct work, sealing projections through the roof. Very easy to apply, cold applied, self-adhesive, good...
Eagle Wet Primer is a solvent-free resin with low viscosity, applying in a single layer to increase adherence of waterproofing systems - use with Desmopol membranes, even on concrete or mortar substrates with high residual moisture.
This glassfibre reinforcing mesh should be used to reinforce Keim render systems.
This product is available as POA. Click here to email us for more information
Britannia Hi-Bond Asphalt Adhesive is a high adhesive bonding agent for use between asphalt and conventional building substrates. Eliminates the need for traditional methods of surface preparation: roughening, scrabbling, rendering and mechanical fixing.
Advantages
Water-based modified rubber solution
Safe and eco-friendly
Orange in colour
For...
Used for roofing applications such as hand lay-up, spray up, centrifugal casting, filament winding, polyester concrete, etc. It is particularly suitable for gel coat curing, and its low viscosity makes it ideal for airless spray-up techniques with external mixing.
Top Features
Density at 20℃ 1,128g/ml
Viscosity at 20℃ 16mPa s
SADT 65℃...
Protection with Dacfill glassfibre reinforcement fleece provides additional mechanical strength and is very easy to apply. Recommended uses are for the reinforcement of the first coat of Dacfill or Dacfill HZ.
Rust-Oleum Mathys Elastofill forms a rubber-like mass with permanently high elasticity (>900%) after evaporation of the water - can absorb strong expansions and deformations - alkali resistant - very resistant to ageing, weather and temperature variations - waterproof - very good adhesion - easy application.
