A reinforcement fleece for the first coat of Murfill Waterproofing Coating on structural surfaces where required. When fleece is introduced it offers maximum durability, flexibility and strength to the system. Made out of polyamide fibres Available in woven in block meshes or non-woven Typically rolled/brushed into the first coat while...
Bullet Roof Fast Prime
Developed for use with the Bullet Roof Rapid system to provide additional key and adhesion, ensuring the optimum bond to the substrate.
- Fast cure time
- Single component-No mixing
- Elastic when cured
- Multi-surface use
Bullet Roof Fast Prime has been developed for use with the Bullet Roof Rapid system to provide additional key and adhesion, ensuring the optimum bond to the substrate.
Curing in times from 2hrs, Fast Prime speeds up installation times without compromising its ability to penetrate the surface/substrate. This low viscosity multi surface polyurethane primer can be used successfully on felt, mineral felt, asphalt, timber, concrete as well as metals.
Please note, Fast Prime must be allowed to fully cure “tack free” prior to overcoating to avoid reactions between coats. The overcoating window is 24hrs. Outside of this time period the surface should be re-primed with Fast prime. If Fast Prime is rained on at any point before overcoating this should be dried off and reapplied in dry conditions. Surface temperatures should be above 5ºC before applying Fast Prime.
Take care not to apply too much product as this will significantly increase cure times. Suitable for general roof/gutter repairs etc.
Top Features & Benefits
- Fast cure time (from 2hrs dependant on outside temperatures)
- Single component-No mixing
- Easy application
- Elastic when cured
- Excellent substrate penetration
- Multi-surface use
Preparation & Application
Clean the surface using a high pressure washer, if possible. Remove oil, grease and wax contaminants. Cement laitance, loose particles, mould release agents, cured membranes must also be removed. Apply using brush or roller at a minimum consumption rate of 100 gr/m² (consumption rate may increase dependant on surface/substrate porosity).
Rollers will not be re-useable. Use a solvent based cleaner to clean tools.
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
- Bullet Building Products
- Brush, Roller
- Touch Dry (at 20°C)
- 1 - 2 hours
- Shelf Life (from date of manufacture)
- Can be kept for minimum 12 months in the original unopened cans in dry conditions and at temperatures of 5-25ºC. Once a can has been opened, use as soon as possible.
- 4kg units
Be the first to ask a question about this product!
Bullet Roof Reinforcement Matting are rolls of polyester geotextile or chopped strand glass rolls for use with Bullet Roof products, available in the following configurations: Bullet Roof Mono Reinforcement Matting (PURG110)Can be used with Bullet Roof Mono and Bullet Roof Rapid. Supplied as a Geotextile 50m x 1m roll. Bullet Mat 100 Glass...
Tordeck DSP is a super-high solids two pack epoxy resin based primer used for the suppression of vapour pressure effects to prevent air/moisture blistering on suspect concrete and asphalt balcony surfaces, suspended decking etc, prior to application of Tordeck two pack systems. Also used in conjunction with Florex Solvent Free Floor Coating.
Rustoleum Dacfill SB Embedment Coat is a high-build basecoat for use in conjunction with Dacfill Glass Fibre Fleece to provide a reinforced base for the Dacfill SB Waterproofing system. Its deep pink colour offers a low sheen finish.
Britannia Aquashield Primer is ideal for porous roofs, and roofs which may break into smaller pieces if pressure is applied, such as concerete, asbestos cladding, sheeting and guttering. Will also prime fibre cement corrugated sheet. Advantages Cures in 1 day Waterproofs instantly Solvent-based 2-year shelf life
Britannia Hi-Bond Asphalt Adhesive is a high adhesive bonding agent for use between asphalt and conventional building substrates. Eliminates the need for traditional methods of surface preparation: roughening, scrabbling, rendering and mechanical fixing. Advantages Water-based modified rubber solution Safe and eco-friendly Orange in...
Eagle Tecnoplastic Rubber Granules is a plastic bead, applied to a fully cured roof to provide a less harsh, non-slip surface for trafficked areas. Good for barefoot traffic areas Use with Tecnotop 2C Available as a 2Kg tub, covering up to 100M2 (depending on density of the mixture)
Gaco Roof Tape is a self-adhesive seam tape made of cross linked polymers of butyl and E.P.D.M. rubber, coated on fleece backing. Gaco Roof Tape maintains its elasticity and splice integrity when subjected to severe ultraviolet rays, thermal shock, ponding water, and extremely low temperatures.
Tor Raincoat APA (RC353) is a single pack coating based on a specially modified acrylic resin system containing anti-corrosive pigments and inert extenders. Tor Raincoat APA is an adhesion promoting and anti corrosive intermediate coating for use in conjunction with Raincoat roof coatings and cladding finishes over PVDF and other plastic coated substrates.
SikaSeal Lead & Gutter is a low modulus, neutral cure sealant specifically designed to give exceptional adhesion to soft metals such as lead, brass etc. The product is specially formulated as an alternative to mortaring Lead Flashing and Sheet into Brick, Stone and Concrete. Features and Benefits Excellent adhesion to metals - will...
Everbuild 902 Bitumen & Flashing Primer is a thin black primer used to give a key prior to applying bitumen paints and roof coatings such as Everbuild 901 Black Bitumen Paint, Everbuild 905 All Weather Roof Coating and Everbuild 906 Bitumen Roofing Emulsion.
Sika MultiSeal BT is a self-adhesive sealing tape made of a butyl rubber compound, protected by a reinforced aluminium metal film. Used for sealing and repairing against water penetration on roofs including sheet metal work, facades, broken roof tiles, leaking roof gutters, chimneys and roof lights, air conditioning piping, caravans and...
Thermilate PRO Roof Primer is a water-based primer specially formulated to prepare clay roof tiles for painting with Thermilate PRO Insulating Roof Coating. Thermilate PRO Roof Primer aids adhesion by producing a bond between clay roof tiles and Thermilate PRO Insulating Roof Coating to avoid flaking or peeling.
Eagle Bitumen Primer provides a key on substrates prior to application of bituminous roof paints and surface coatings, applying by brush or sprayer, and requires no thinning. Use on substrates and surfaces that include: Ready for use Suitable for use with all bituminous surface coatings Used for priming concrete roofs and floors,...
Tor Raincoat Stabilising Sealer (RC351) is a modified acrylic resin based, low viscosity solution containing a biocidal additive and organic solvents. Tor Raincoat Stabilising Sealer is for the priming/stabilising of bare, cementitious (eg. asbestos cement, fibre cement etc) porous and friable pitched roofing substrates prior to application of Raincoat...