Tor Elastamat Regular (SS6000116 / SS6000025RL / SS6000830) is a random weave chopped strand glass fibre mat (nominal 100g/m²) for the reinforcement of Tor liquid applied roof waterproofing systems. It is used as a full reinforcement on flat roof applications and where ponding is evident, and as localised or partial reinforcement in other areas.
Bullet Roof GRP Hardener
Used for roofing applications such as hand lay-up, spray up, centrifugal casting, filament winding, polyester concrete, etc. It is particularly suitable for gel coat curing, and its low viscosity makes it ideal for airless spray-up techniques with external mixing.
- Density at 20℃ 1,128g/ml
- Viscosity at 20℃ 16mPa s
- SADT 65℃
- Flash point 60℃
Bullet Roof GRP Hardener is used for roofing applications such as hand lay-up, spray up, centrifugal casting, filament winding, polyester concrete, etc. It is particularly suitable for gel coat curing, and its low viscosity makes it ideal for spray-up techniques (airless) with external mixing.
The factors to be considered in selecting the optimum initiator / acclerator system are:
- Resin Type
- Required gel time or pot life
- Part thickness
- Room temperature
- Nature and quantity of additives
- Dosage optimisation between Sentinel Hardener and accelerator
Bullet GRP hardener is Methyl Ethyl Ketone Peroxide used for the cure of unsaturated polyester resins at room temperature in combination with a cobalt accelerator.
Top Features & Benefits
- Density at 20℃ 1,128g/ml
- Viscosity at 20℃ 16mPa s
- SADT (self-accelerating decomposition temp) 65℃
- Flash point (setapoint) 60℃
Bullet GRP hardener is recommended for the curing of ortho- and isophtalic resins at temperatures between 15℃ and 50℃. Concentration at a rate of between 1 and 4% by weight based on resin, depending on weather conditions.
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
- Shelf Life (from date of manufacture)
- Product can be stored maximum three months after receiving date, if kept in appropriate conditions and below its maximum storage temperature. Refer to the safety data sheet for detailed storage instructions.
- 1KG or 5KG
Be the first to ask a question about this product!
A specially-formulated primer for application on to metals to enhance adhesion properties, and allow the primer to physically bond onto the metal using an incorporated activating acid that "etches" into the substrate. Advantages For Aluminium, Copper and Galvanised Steel surfaces. White in colour. Upto 12-months shelf life.
Tor Elastaseal Z Binder Sealer (RC144) is a two component, moisture curing polyurethane resin solution for use as an all-aliphatic stabilising sealer and primer on a wide range of substrates such as concrete, asphalt, bitumen, felt, asbestos, plaster, render, etc. Coverage Calculator
GacoFlex E5320 2-Part Epoxy Primer/Filler is a two-component, water-based epoxy primer that is ideal for use on most roofing surfaces including metal roofs and flashings. This easy-to-apply primer bonds to properly prepared roofing surfaces and improves adhesion of GacoFlex silicone coatings and other top coats, especially on weathered...
A unique product that enables damp, moist and green concrete to be primed at surface temperatures of +5 degrees and rising saving large amounts of down time. It cures rapidly to from a DPM or damp proof membrane. Top Features VOC close to “0” and water based Forms an effective barrier against negative/back pressure Forms a damp and...
Tor Elastaseal Z Fibretex (RC142) is a cold applied single pack, high solids, moisture activated, elastomeric urethane coating, containing inert reinforcement fibres. For use as a high build, heavy duty, fibre loaded stripe coating, free from solvent odour that provides durable, long term protection for roofs. Coverage Calculator
Tor Elastascrim BT is a non-flammable, butyl, rubber based, self-adhesive tape with a polymeric textile reinforcement protection fleece. Used for the bridging of roof sheet lap joints, stabilised cracks, movement joints, small gaps, abutment details etc, prior to application of Tor roof waterproofing and protective coating systems etc.
Torprufe FS Primer (RC253) is a stabilising and bonding primer for use on new and weathered smooth bitumen based felts prior to application of Tor water based roof coatings (Torprufe CRC, Elastaseal WB etc). May also be suitable (subject to test) over synthetic carrier membranes. Also as a substrate bonding primer for installation of TorVap VCL / CM in...
Rust-Oleum Dacfill SB Primer is a stabilising sealer and primer for use on a wide range of substrates. It is a single component, moisture-curing solvent-based polyurethane resin solution to be used as a surface stabiliser/adhesion promoter for degraded felts, asphalt etc. and porous mineral substrates.
GacoFlex 66S Tape is a low profile, fusion-bonded polyester fiber designed to form a strong, yet conforming, membrane for silicone elastomeric coatings on uneven surfaces. Used for plywood joints, concrete construction joints, concrete cracks, and joints between metal, fiberglass or insulation, and combinations of the above substrates in roof,...
Tor Elastascrim FT (SS6000140) is a non-flammable, semi-elastic, putty-like butyl rubber based strip encapsulant/sealant. Supplied in roll form on siliconised paper release backing for use as a formable pre-coat encapsulant and sealant over roof sheet bolts etc. Also usable as a lap joint gap filler/sealer on sheeted (profile metal, fibre-cement etc)...
Sika Reactivation Primer is a one-component primer for the reactivation of existing Sika Roofing and Balcony systems. Used on Sikalastic 621 TC and Sikafloor 405/415 polyurethane systems. Features and Benefits Allows further coats to be safely applied when the standard re-coating window has been exceeded Single pack Quickly and easily...
Britannia Hi-Bond Asphalt Adhesive is a high adhesive bonding agent for use between asphalt and conventional building substrates. Eliminates the need for traditional methods of surface preparation: roughening, scrabbling, rendering and mechanical fixing. Advantages Water-based modified rubber solution Safe and eco-friendly Orange in...
Eagle Anti-Slip Slate Grit applies to a fully cured roof to provide a non-slip surface for heavily trafficked areas. Use with Desmopol, Ultraflex or a relevant top coat. Coverage rate approx. 25-30M2 per 10Kg
Tor Elastaseal FIA Gun Cleaner (SS1000003E8) is used to clean out the Tor Elastaseal FIA Application Gun after use. It flushes out remaining adhesive leaving the gun mechanism clean and ready for use.
Tor Elastaseal FIA (Foaming Insulation Adhesive) is a fast curing polyurethane based aerosol foaming adhesive, applied by special aerosol gun, it meets Fire Class B1. Elastaseal FIA should be used for the bonding of roofing insulation boards to roofing substrates and membranes including asphalt, felt, vapour control layers, aged single ply membranes, etc.