Eagle Anti-Slip Slate Grit applies to a fully cured roof to provide a non-slip surface for heavily trafficked areas. Use with Desmopol, Ultraflex or a relevant top coat. Coverage rate approx. 25-30M2 per 10Kg
Rust-Oleum Mathys Primer 44 HS
Rust-Oleum Mathys Primer 44 HS has a large fixation capacity for stabilising loose particles and improving the adherence of subsequent topcoats.
Features and Benefits
- Good UV resistance
- Excellent fixation on roofs
- Very flexible
- Chlorinated rubber technology, solvent-based
- Quickly water-resistant (1 hour after application at 20 °C)
Rust-Oleum Mathys Primer 44 HS
Large fixation capacity for stabilising loose particles – improves the adherence of subsequent topcoats – Unsaponifiable – good UV resistance – flexible, fixation layer for porous and unpainted mineral substrates
- Density: 1,1
- Gloss Level: Gloss
- Solids content in volume: 32 %
- Solids Content in weight: 45 %
Drying Times At 20°C/RH 50%
- Touch dry: 1 hour
- Dry to handle: 1 hour
- Dry to recoat: 24 hours
- Fully cured: 24 hours
10 - 15 m²/l. Practical coverage depends on many factors such as porosity and roughness of the substrate and material losses during application.
Further information can be found on the product data sheet.
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
- Brush, Roller, Spray
- Dry to Handle (at 20°C)
- 1 Hour
- Dry to Recoat (at 20°C)
- 24 Hours
- Fully Cured (at 20°C)
- 24 Hours
- 14m² per litre
- Min. Application Temperature
- Solids by Volume
- 32 %
- 599 g/l
- Shelf Life (from date of manufacture)
- 2 years from date of production in unopened cans, if stored in dry, well ventilated areas, not in direct sunlight at temperatures between 5° and 35°C.
- Touch Dry
- 1 Hour
- Recommended Dry Film Thickness
- 23 µm
- Recommended Wet Film Thickness
- 70 μm
- UN Number
- 10 - 15 m²/l
|darren on 2017-03-23 15:22:35|| |
Question: can i use mathys primer 44 on exterior lime rendering ?? thanks
As long as the lime render is in good condition, clean, prepared, etc, then Rust-Oleum Mathys Primer 44 HS would be our normal priming solution prior to applying suitable topcoat(s).
Tor Elastascrim BT is a non-flammable, butyl, rubber based, self-adhesive tape with a polymeric textile reinforcement protection fleece. Used for the bridging of roof sheet lap joints, stabilised cracks, movement joints, small gaps, abutment details etc, prior to application of Tor roof waterproofing and protective coating systems etc.
Tor Elastaprime (RC100) is a high performance universal primer that provides excellent binding and adhesion to most substrates including plastics, wood, mineral substrates, ceramic tile, copper, zinc, brass, steel, galvanised steel, aluminium etc. Tolerant of low temperature/high humidity conditions. Used in conjunction with Tor Elastaseal,...
Tor Elastamat Regular (SS6000116 / SS6000025RL / SS6000830) is a random weave chopped strand glass fibre mat (nominal 100g/m²) for the reinforcement of Tor liquid applied roof waterproofing systems. It is used as a full reinforcement on flat roof applications and where ponding is evident, and as localised or partial reinforcement in other areas.
Tor Elastaseal FIA (Foaming Insulation Adhesive) is a fast curing polyurethane based aerosol foaming adhesive, applied by special aerosol gun, it meets Fire Class B1. Elastaseal FIA should be used for the bonding of roofing insulation boards to roofing substrates and membranes including asphalt, felt, vapour control layers, aged single ply membranes, etc.
Tor Elastamat HD (SS6000225) is a random weave chopped strand glass fibre mat for high strength reinforcement of Tor liquid applied roof waterproofing systems. It is used as a full reinforcement on heavy duty flat roof applications and where ponding is evident, and as localised or partial reinforcement in other areas.
Tordeck DSP is a super-high solids two pack epoxy resin based primer used for the suppression of vapour pressure effects to prevent air/moisture blistering on suspect concrete and asphalt balcony surfaces, suspended decking etc, prior to application of Tordeck two pack systems. Also used in conjunction with Florex Solvent Free Floor Coating.
Sika Flexitape Heavy Duty is used for additional partial reinforcement under Sika Reemat Premium on cracks/joints subject to movements of >15% (expansion joints) and to bridge smaller seams between different substrates. Expansion joints require special advice with a release adhesive tape.
Tor Elastascrim FT (SS6000140) is a non-flammable, semi-elastic, putty-like butyl rubber based strip encapsulant/sealant. Supplied in roll form on siliconised paper release backing for use as a formable pre-coat encapsulant and sealant over roof sheet bolts etc. Also usable as a lap joint gap filler/sealer on sheeted (profile metal, fibre-cement etc)...
Strong roof trims that produce a beautiful finish with pre-made corners that allow effortless change between a raised edge and drip detail. Made using "E" type glass reinforcement encapsulated in thermo set polyester resin to give outstanding life expectancy and performance. Full details of available sizes, ranges and installation...
Britannia Aquashield Primer is ideal for porous roofs, and roofs which may break into smaller pieces if pressure is applied, such as concerete, asbestos cladding, sheeting and guttering. Will also prime fibre cement corrugated sheet. Advantages Cures in 1 day Waterproofs instantly Solvent-based 2-year shelf life
GacoFlex 66S Tape is a low profile, fusion-bonded polyester fiber designed to form a strong, yet conforming, membrane for silicone elastomeric coatings on uneven surfaces. Used for plywood joints, concrete construction joints, concrete cracks, and joints between metal, fiberglass or insulation, and combinations of the above substrates in roof,...
The new Tortrim range has been developed to provide detail plastic trims to produce a neat edge to Tor roof systems. Bond It PU18 is a one part moisture curing polyurethane fast grab adhesive/sealant for bonding trim pieces together.
Tor Raincoat Stabilising Sealer (RC351) is a modified acrylic resin based, low viscosity solution containing a biocidal additive and organic solvents. Tor Raincoat Stabilising Sealer is for the priming/stabilising of bare, cementitious (eg. asbestos cement, fibre cement etc) porous and friable pitched roofing substrates prior to application of...
Protection with Dacfill glassfibre reinforcement fleece provides additional mechanical strength and is very easy to apply. Recommended uses are for the reinforcement of the first coat of Dacfill or Dacfill HZ. Improves mechanical strength in Dacfill, Dacfill SB or Dacfill HZ systems Easy to work with Easy to tear, ideal for finishing...
Tor Elastaseal Z Binder Sealer (RC144) is a two component, moisture curing polyurethane resin solution for use as an all-aliphatic stabilising sealer and primer on a wide range of substrates such as concrete, asphalt, bitumen, felt, asbestos, plaster, render, etc. Coverage Calculator