Nu-Guard High Solids Finish, a two-component polysiloxane-based anti-graffiti coating for use on external surfaces such as painted brickwork, render, concrete, metal, wood and vehicles, with an excellent decorative appearance and outstanding solvent and chemical resistance. Click to jump down to Technical Data Available in clear and 280+...
Keim MX Glaze Clear
A high performance epoxy and a polyurethane in one coat. General purpose high gloss coating offering good weathering and wear resistance.
- Very low odour
- Gloss in appearance
- Finish: Gloss
This product is available as POA. Click here to email us for more information
An engineered siloxane coating that embodies the properties of both a high performance epoxy and a polyurethane in one coat. General purpose high gloss coating offering good weathering and wear resistance. Provides a wipeable, durable surface that has good anti-graffiti properties for all mineral substrates.
Top Features & Benefits
- Very low odour.
- Gloss in appearance.
- Finish: Gloss.
- VOC: 8% by weight / 120g/l.
- Specific gravity: 1.36kg/l (mixed product).
- Pot life: 4 hours (200C).
- Drying times: at 125 µm dft and 200C in hours.
- 300C 200C 100C 50C.
- Dry to touch 1 2 4½ 7.
- Dry through 3 4½ 8½ 16.
- Mixing ratio (by volume): 4 parts resin: 1 part cure.
Product Use in the Workplace
All loose, flaking and unstable material must be identified and then thoroughly removed, all surfaces must be thoroughly washed down with clean cold water to remove all surface dirt and dust. When all surfaces are clean, sound, wind dry, dust free and free from all surface contaminants, decoration using KEIM MX Glaze may proceed.
KEIM MX Glaze is supplied in the proper mixing proportions of resin and cure. Add cure to resin and stir thoroughly with mechanical mixer for five minutes, avoid entrapment of air in the coating which will result in bubbles and blisters. Apply a thin and even coat by brush or short pile roller.
Ambient and substrate temperature above 5°C and below 30°C. Do not apply in direct sunlight or onto sun-heated surfaces, nor if it is raining or if there is an immediate likelihood of rain.
Approx. 0.1lt/m2 per coat. Consumption rates are offered for guideline purposes only and are quoted for smooth surfaces. Actual rates are the responsibility of the applicator. Project specifications should be referred to for specific rates.
Cleaning of Tools
Clean tools with solvent immediately after use.
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
Be the first to ask a question about this product!
Coo-Var WB101 Anti Graffiti Coating is a two pack water based surface sealer for application to masonry surfaces to reduce surface absorbency and ensure ease of cleaning in hygienic locations. The ideal way to combat unwanted graffiti. Can be applied to masonry, brick, plaster, wood and previously painted surfaces by brush or roller to give a...
Tor Torlife TP Coloured, a 2-pack high performance anti-graffiti, anti-vandal finish coat for the Torlife TP Coloured System, available in over 400 RAL and BS colours. For external surfaces on nearly all building types Use in communal areas and industrial environments Non-sacrificial anti-graffiti finish Extremely durable with UV colour...
Rust-Oleum GraffitiShield Spray Pump 8L is the ideal tool for easy the application of Rust-Oleum GraffitiShield Wax and Hydro. Hiring an airless spray machine or employing a professional to apply these anti-graffiti coatings can be costly. By using the Rust-Oleum GraffitiShield Spray Pump you can save time on application and achieve the same...
Blackfriar Professional Anti Graffiti Lacquer is an exterior, high performance solvent based lacquer that provides an easy-to-clean, permanent (non-sacrificial) polyurethane coating against multiple graffiti attacks. Allows problem areas to be cleaned easily and effectively. Product Features Designed to allow easy removal of permanent...
Nu-Cryl® AG Extra is a highly durable anti-graffiti coating for use on external walls made of granite, marble, brick, polished concrete and GRC. Tested to BS 476 parts 6&7 and satisfies Class '0' requirements of current Building Regulation. Advantages Protection from graffiti Resistance to weathering/UV No reapplication required...
Nu-Guard® Tack Primer gives you the base coat on which to apply the Nu-Guard AG System to non-porous or existing coatings. Advantages Exceptional adhesion to non-porous surfaces. Primer coat for the Nu-Guard AG System. Touch Dry from 3-4 hours. Water soluble. 12-month Shelf life.
Mathys Pegagraff Hydro is a clear coating designed to protect a range of bare and previously painted surfaces inside and out from graffiti attack. Can be used on floors, walls and other surfaces to create a tough, clear glaze that can be easily and frequently cleaned to remove any unwanted graffiti that may occur. Colourless anti-graffiti...
Rust-Oleum GraffitiShield Wax is a biodegradable, semi-permanent wax-based anti-graffiti coating, suitable for use on surfaces in need of protection against graffiti and other pollutants. It instantly forms a sacrificial layer based on natural wax that is suitable for a single cleaning process. Rust-Oleum GraffitiShield Wax should be...
Sikagard 850 AG is a permanent anti-graffiti and anti-flyposter coating that needs no refreshing coat after cleaning, which can be performed many times. Use for the protection of concrete, wood, masonry and metal substrates. Wash away graffiti with cold water and a clean cloth No chemical agent is required for cleaning Poster prevention...
Rust-Oleum GraffitiShield Polycoat is a single pack, solvent-free clear anti-graffiti coating that provides a permanent anti-graffiti barrier that can be frequently cleaned without the need to re-apply. 1 coat application for interior and exterior areas. Hard, smooth surface makes it easy to clean any graffiti on it Solvent-free, low odour...
Coo-Var GP101 Graffiti & Flyposting Protection System is a clear surface coating, available in a matt and gloss finish, offering excellent protection against graffiti and poster vandalism. Product Features Apply after Coo-Var GP101 Anti-Graffiti Sealer Coat on porous surfaces. Can be used on a wide range of clean, prepared rough or...
Nu-Guard AG is a unique, one coat anti-graffiti coating that protects all surfaces, including brick, concrete, render, stone, wood and plastic against all types of graffiti and poster glues. It’s been completely re-engineered in England to provide the most vandal resistant finish ever achieved anywhere in the world.
Nu-Flame AG Colourcoat is a pigmented and smooth fire retardant coating with anti-graffiti properties. Water-soluble, easy to clean and available in BS 4800 shades. Advantages Water-soluble urethane coating. Safe for internal applications. Easy to clean. BS 4800 shades. Graffiti resistant. UV stable. 10-12m²/Litre coverage.
Bradite Poly Lacquer is a two-pack polyurethane, clear coating and finish lacquer, for steel, non-ferrous metals, wood, concrete & mineral substrates free of contamination, dust, efflorescence and properly prepared. Manufactured under the auspices of an ISO 9001:2008 & ISO 14001:2004. Advantages Available in more than 350 colours...
Nu-Guard WB Concrete Sealer is a modified Vinyl Acetate, non-flammable and non-toxic sealer. It is formulated primarily for use on concrete and brickwork. Nu-Guard WB Concrete Sealer primes/seals very porous surfaces and prevents the darkening of light substrates prior to the application of Nu-Guard AG Clear and Coloured Finishes.