Coo-Var GP101 Anti-Graffiti Sealer Coat is recommended before our Anti Graffiti protection system is applied on porous surfaces. A transparent sealer which offers excellent water and mildew resistance. Being acrylic based and free of volatile organic solvents this sealer is low odour, non flammable and has low toxicity. This can be used to...
Coo-Var GP101 Graffiti & Flyposting Protection System
Coo-Var GP101 Graffiti & Flyposting Protection System is a clear surface coating, available in a matt and gloss finish, offering excellent protection against graffiti and poster vandalism.
- Apply after Coo-Var GP101 Anti-Graffiti Sealer Coat on porous surfaces
- Can be used on a wide range of clean, prepared rough or smooth surfaces
- Retains the appearance and aesthetic of the original surface
- Prevents permanent marking by graffiti, which can easily be cleaned using water or mild cleansing agents
- Makes Fly Posters easy to remove
- Posters just peel off and graffiti can be removed quickly and easily with water or water with mild detergent (DO NOT USE ANYTHING STRONGER)
Coo-Var GP101 Graffiti & Flyposting Protection System is a single pack, revolutionary, clear coating which offers long term protection against both graffiti and flyposters. Due to how fast drying the product is, it allows two coats to be applied in one day. This means less time on application and reduces the chances of graffiti attack between coats which can be a serious issue for other slower drying systems.
Coo-Var GP101 Graffiti & Flyposting Protection System allows all types of graffiti attack to be removed using only soapy water. This means whenever graffiti occurs, it can be removed quickly and safely by anyone, no special skills or equipment is needed and no harmful, strong solvents or cleaners are required.
Remove existing graffiti with dedicated graffiti removal agents where required. Ensure that the underlying surface is free of any residue from graffiti removal agents. The surface must be clean, sound and free of any dust, dirt, oil and grease. If necessary wash the surface with high pressure water and allow to dry. Adhesion should be checked over all surfaces as follows to ensure suitability of GP101.
Dab GP101 with a small rag onto a small area of the surface (5-10cm² is sufficient) and allow to dry overnight. For signage and murals, after sufficient dry time has elapsed, rub firmly across the test area with finger for loss of adhesion. For other painted surfaces, rub firmly with a rag soaked with Thinners 14, then rub the surface by hand. If there is no evidence of GP101 peeling off the surface is compatible.
Stir well before use and use manageable quantities. Pour a small quantity into roller tray or spray unit as required. Then reseal the container immediately. GP101 has a pot life of approximately two hours when exposed to the elements, which can vary depending on the ambient
As dictated by normal good painting practice. In confined spaces, provide adequate ventilation during application and drying.
Coo-Var Anti-Graffiti Sealer Coat on porous and natural surfaces such as sandstone. Apply directy to non porous brick work and masonry.
Please contact Rawlins Paints' Technical Support Team on 0113 2455450 for more information.
- For Use By
- General Use
- Water / Solvent Based
- For Use On
- Single, Two or Three Pack
- Pack Size
- Brush, Roller, Spray
- Touch Dry (at 20°C)
- 1 to 2 hours
- 8-10m² per litre
- Recommended Thinner/Cleaner
- Do Not Thin
- Solids by Volume
- Touch Dry
- 1-2 Hours
- UN Number
- Base Type
- Exterior / Interior Use
- Exterior & Interior Use
- Suitable For Use On
- Suitable For Use On
- Suitable For Use On
- Single Pack
- Permanent / Semi-Permanent
|Beth Morgan on 2023-01-11 14:05:25|| |
Hello, I am an artist who is going to be undertaking an outdoor mural on brick. I will be using water based masonry paint to create the mural and I am required to coat it with an anti-graffiti coating. I have been looking at Coo-Var GP101 Graffiti & Flyposting Protection System - I wanted to ask if this would be suitable to use over a painted mural, and if so, would an initial sealer coat be required or would I be able to use the Graffiti and Flyposting Protection alone? Many thanks in advance. Beth
Answer from Rawlins’ Technical Team:
Assuming the previously painted wall is fully cured, clean, dry, sound and prepared as detailed in the technical data sheet this could be used.
We would recommend a test for compatibility and adhesion is undertaken prior to full application.
The Coo-Var Anti-Graffiti Sealer Coat is only required on porous substrates such as sandstone.
Coo-Var GP101 Graffiti & Flyposting Protection System is a clear surface coating, available in a matt and gloss finish, offering excellent protection against graffiti and poster vandalism. Apply after Coo-Var GP101 Anti-Graffiti Sealer Coat on porous surfaces Can be used on a wide range of clean, prepared rough or smooth surfaces...
General Painting Application Kit from Rawlins Paints provides the basics for any painting project. Whether it is a one off job, or you just want to make sure the right application tools get to site. Provides an economical way of making sure you will have what you need Ideal for interior and exterior paint projects Click to jump down to...