Limited sizes, finishes and colours available. See options below for available quantities.
HMG HB48 Primer is an alkyd based, quick drying primer offering outstanding adhesion, moisture resistance and corrosion protection due to incorporation of modified Zinc Phosphate.
HMG data sheets (see section above) indicate a dry film thickness that will be achieved when applying a particular wet film thickness
These values are a guide only and are not to be used as specifications
Film thickness will vary depending on actual use and specification
Great care should be taken to achieve the dft stated in the agreed specification and to avoid areas of excessively low or high thickness
Drying Times
Drying Times At 20°C
Touch Dry:
20 - 30 minutes
Hard Dry:
3 hours
Full Dry:
24 hours
Surface Preparation
Ensure surfaces to be coated are dry and must be cleaned using the appropriate HMG product to remove all traces of contaminants
Read and follow the safety data sheet, product data sheet and label instructions
Stir all paints thoroughly before use
Always use the same batch number on the same job
Check colour & sheen
Filter the product immediately before use
Reduce emissions and maintain quality by replacing tin lid after use
Substrates: HMG HB48 Primer is suitable as a primer coat for suitably prepared metals, clean and free of grease, oils and other contaminants. Not suitable for coating over bitumen or chlorinated rubber coatings.
Application Climate: Substrate temperature should be 5⁰C or above for application and during cure, and a minimum of 3⁰C above the dew point. Adequate dry air ventilation should be supplied during drying.
Application Information: Thinning should only take place after material is thoroughly mixed. Application and use should always conform with the codes of practice described in BS 6150 and BS 5493.
Surface Preparation: Ensure surfaces are clean, dry and free from grease, oils, dust and other contamination prior to application. Thoroughly clean and degrease using suitable:
Mild Steel – Remove millscale and thoroughly degrease using suitable HMG Prep Clean - abrade with P80 – P180 if necessary, prior to application of primer
Shot Blasted Steel – Remove all traces of blast grit/sand prior to application of primer
Aluminium – Abrade with P180 – P320, degrease with suitable HMG Prep Clean prior to application of primer
Galvanised Steel – Degrease with suitable HMG Prep Clean, apply HMG Mordant Wash, apply HMG Etch Primer and if required use appropriate HMG Primer
Previously Painted:
High pressure wash to remove all loose debris and poorly adhered previous coatings to remove all salts and other contaminants
Degrease using suitable HMG Prep Clean 2800 to remove grease and oils not removed with pressure washing alone
Existing coatings to be well adhered with all edges tight and well feathered Rust/corrosion to be removed back to clean metallic appearance
Abrade to provide good adhesion
Wipe over with degreaser to remove loose debris from abrasion
Substrate to be clean, free of grease, oils, dust and completely dry prior to application
For further information on mixing ratios please contact Rawlins Paints Technical - 0113 2455450 (option 2) or [email protected]
Health & Safety
Refer to the safety data sheet in the attachments section above and tin label prior to use
Suitable respiratory equipment should be worn when spraying
Contaminated Rags, Spray Booth Filters or other substrates should be segregated from other chemical waste, soaked with Water and disposed of in a non-combustible container with a tight fitting lid
Designed for airless or conventional application for structural steelwork, chassis, steel fabrication etc. It is easy to apply without fear of runs or sags at high wet film thickness.
Touch Dry (at 20°C)
20 - 30 Minutes
Dry to Handle (at 20°C)
3 Hours
Fully Cured (at 20°C)
24 hours
Coverage
10m² per Litre
Recommended Thinner/Cleaner
Thinner 2621
Solids by Volume
55%
VOC
0.450 Kg/l
Shelf Life (from date of manufacture)
12 months from delivery date in original sealed containers
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
CLEARANCE - HMG HB48 Primer is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
HMG QAD Enamel is an industrial, durable, high gloss, tough alkyd for use on spray applied steel, railings, exterior furniture and fencing plus other suitable prepared metals.Quick drying - touch dry in 30 minutes Coverage: 11-12m² per litre at 20 microns dft, 10-12 m² per litre at 55 microns dft Can be applied to mild, galvanised and...
HMG Mordant T Wash is designed for use as an etching solution for galvanised steel & zintec.Manufactured to a formulation originally developed by the British Rail Board Click to jump down to Technical DataCoverage Calculator More Information Delivery Info
HMG Chromate Free Etch Primer is a quick drying chromate free etch primer providing good anti corrosive properties and excellent adhesion to ferrous and non-ferrous metals. This product MUST be purchased/used in conjuction with its manufacturer specified base or activator when used as a wash primer:2-Pack System DetailsBase...
HMG Prep Clean 2802 is a fast evaporating, strong Preparatory Cleaning solvent for the heavy duty degreasing of substrates.Used in many applications For use on bare surfaces onlyMore Information Delivery Info
HMG Prep Clean 2804 is a water based preparatory Cleaner for the degreasing of substrates.Used in many applications For use on bare surfaces onlyMore Information Delivery Info
HMG Prep Clean 2803 is a slow evaporating, low odour and mild preparatory cleaning solvent for the degreasing of substrates.Used in many applications For use on bare surfaces onlyMore Information Delivery Info
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools)1 x Rust-Oleum...