• Reduced price

HMG PVC17 Colours - CLEARANCE

TOPPVC17 - CLEARANCE
HMG8550
  • Satin - RAL 9010 - 1L x 7

HMG PVC17 Colours is a 1K vinyl acrylic with exceptional flexibility and adhesion. HMG PVC 17 is suitable for coating most PVCu, hard plastics (not GRP) and powder-coated surfaces (architectural cladding).  If in doubt, a small trial should be carried out in a localised area to ensure adhesion and compatibility with the surface.

Please note: Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour.

Coverage Calculator

Colour
Size
Finish
£27.39
£6.85(ex. VAT) Save 75%
£8.22 (inc. VAT)
Quantity
Product not available
Last Items in Stock and Available for Delivery (See Delivery Options Below)

Description

HMG PVC17 Colours is a 1K vinyl acrylic with exceptional flexibility and adhesion.  HMG PVC 17 is suitable for coating most PVCu, hard plastics (not GRP) and powder-coated surfaces (architectural cladding).  If in doubt, a small trial should be carried out in a localised area to ensure adhesion and compatibility with the surface.

PVC17 is not suitable for coating areas incorporating draught seals and gaskets.



Click To Jump To Section:




Features & Benefits




Product Specification


Technical Data
Volume Solids: 28.9%
VOC Content: 0.745Kg/L
SG: -
Viscosity: 200 mPas
Density: 100 mPas
Storage Conditions: Store between 5°C - 25°C.  When not in use, cans must be kept sealed.
Shelf Life: 12 months from delivery date in original sealed containers.
Flash Point: - 9°C



Film Thickness Range And Coverage


Product Data
  Dry Film Thickness Wet Film Thickness
Compliant Spray Gun: 25 µm 100 µm
Brush: 25 µm 100 µm
Pressure Pot: - -



Coverage: 10 square metres per litre @ 25 microns dft. 

  • HMG technical data sheets indicate a dry film thickness that will be achieved when applying a particular wet film thickness.
  • These values are a guide only and are not to be used as specifications.
  • Film thickness will vary depending on actual use and specification.
  • Great care should be taken to achieve the dft stated in the agreed specification and to avoid areas of excessively low or high thickness.



Drying Times


Drying Times At 20°C/RH 50%
Touch Dry: 15 minutes
Dry To Recoat: Minimum of 1 hour
Fully cured: 8 hours



Surface Preparation


  • Ensure surfaces to be coated are dry and must be cleaned using the appropriate HMG product to remove all traces of contaminants.
  • PVC curtain material and other flexible substrates are best coated after they have been aired, to ensure that any trapped plasticisers can escape.  These need to be released/removed from the surface to ensure correct adhesion and drying of PVC 17. Failure to remove plasticiser will cause adhesion and drying problems.
  • New PVC curtain material and other flexible substrates should be exposed to the atmosphere for at least 7 days to ensure optimum adhesion and drying performance.



Application Methods


Technical Data
Compliant Spray Gun Brush Pressure Pot
Mixing Ratio: Base: 100 Base: 90 Base: 100
Thinner: < 25 n/a Thinner: < 25
Thinner Options: Thinner 2661 - Thinner 2661
Thinner 2604 - Thinner 2604
Viscosity: 30-35 secs B4 Cup - 30-35 secs B4 Cup
Spray Gun Setup: 1.6 - 1.8 - -
Number Of Coats (Guide Only): 1 - 2 full coats 1 coat 1 - 2 coats
Flash Off: 10 - 15 minutes between coats 10 - 15 minutes between coats 10 - 15 minutes between coats



For further information on mixing ratios pleaes contact Rawlins Paints on  Tech - 0113 2455450 (option 2) or [email protected] Sales - 0113 2455450 or [email protected]

Product Notes


Information on basic physical and chemical properties
Form: Liquid
Colour: According to product specification.
Odour: Characteristic
Odour Threshold: Not determined
pH-value: Not determined
Change in Condition
Melting point/freezing point: Undetermined
Initial boiling point and boiling range: 79°C
Flash Point: -9°C
Flammability (solid, gas): Not applicable
Ignition temperature: 315°C
Decomposition temperature: Not determined
Auto-ignition temperature: Product is not selfigniting
Explosive properties: "Product is not explosive. However, formation of explosive air vapour mixtures are possible."
Explosion limits: Lower: 1.2 Vol %
Explosion limits: Upper: 11.5 Vol %
Vapour pressure at 20°C: 10,400 hPa
Density at 20°C: 0.947 g/cm³
Relative density: Not determined
Vapour density: Not determined
Evaporation rate: Not determined
Solubility in / Miscibility with water: NOT MISCIBLE
Partition coefficient: n-octanol/water: Not determined
Viscosity: Dynamic at 20°C: 100 mPas
Viscosity: Kinematic: Not determined
Solvent content: Organic solvents: 71.1%
Solids content: 28.9%



Health & Safety

  • Refer to the safety data sheet in the attachments section above and tin label prior to use.
  • Suitable respiratory equipment should be worn when spraying.

Click to go back to the top of the page

Product Details
TOPPVC17 - CLEARANCE

Data sheet

Manufacturer
HMG Paints Limited
For Use On
uPVC, Powder Coatings,
Application Method
Brush, Spray
Sheen
Satin, Gloss
Colour
Fully Tintable
Single, Two or Three Pack
Single
Touch Dry (at 20°C)
15 Mins
Dry to Recoat (at 20°C)
Minimum of 1 hour
Fully Cured (at 20°C)
8 Hours
Density
100 mPas
Solids by Volume
28.9 %
VOC
0.745Kg/L
Shelf Life (from date of manufacture)
12 months from delivery date in original sealed containers.
Finish
Matt, Satin and Gloss
Recommended Dry Film Thickness
25 µm
Recommended Wet Film Thickness
100 µm
UN Number
UN1263
Fastest Delivery
Next Working Day
Brand
HMG

Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send
COVERAGE CALCULATOR
Units
Film Thickness
Total area²
Or enter length and width dimensions:
Length
Width

*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage

    

You might also like

HMG Thinner 2604

HMG Thinner 2604 is a slow thinner. For use with compatible HMG systems. More Information Delivery Info

Price £10.24 (ex. VAT)
In Stock and Available for Delivery

HMG Thinner 2661

HMG Thinner 2661 is a standard thinner. For use in HMG PVC 17 More Information Delivery Info

Price £11.88 (ex. VAT)
In Stock and Available for Delivery

HMG PVC17 Colours Aerosol

HMG PVC17 Colours Aerosol is a Vinyl Acrylic Aerosol with exceptional flexibility and adhesion. For direct application to plastic substrates. HMG PVC 17 is suitable for coating most PVCu, hard plastics (not GRP) and powder-coated surfaces (architectural cladding).  If in doubt, a small trial should be carried out in a localised area to ensure...

Price £32.05 (ex. VAT)
In Stock and Available for Delivery