Limited sizes, finishes and colours available. See options below for available quantities.
Rust-Oleum 9200 Rust-O-Thane is a satin, water based polyurethane for a very durable and colourfast finish on coated floors, walls and primed metal. Especially recommended where general urethane performance like excellent weather resistance (UV), easy cleaning and abrasion resistance is required.
Rust-Oleum`s hard wearing, washable polyurethane coating (9200) is now also available in convenient 1 litre packaging. Ideal for smaller projects the new convenient 2-component packaging provides the base and activator in one convenient kit and the activator is supplied with a user-friendly spout cap.
Rust-Oleum 9200 Rust-O-Thane is a satin, water based polyurethane for a very durable and colourfast finish on metal. Rust-Oleum Rust-O-Thane 9200 is intended for application on substrates, which are coated with Rust-Oleum or Mathys epoxy or acrylic coatings (e.g. Rust-Oleum 9100 and Rust-Oleum 5401 Epoxy Impregnation Primer or Mathys Pegasol and Pegalink).
The application area consists of coated floors, coated walls and primed metal. Rust-Oleum 9200 Rust-O-Thane assures appropriate protection against solvents, moderate alkalines, weak acids and chemical cleaning.
Rust-Oleum 9200 Rust-O-Thane is especially recommended where general urethane performance like excellent weather resistance (UV), easy cleaning and abrasion resistance is required.
Rust-Oleum 9200 Rust-O-Thane is also suitable to be used on uPVC substrates.
Features & Benefits
Available in 4,000+ RAL, NCS, and British Standard colours
Very durable and UV-resistant, colour and gloss retention
Very easy to clean (also with chemicals)
Very low odour, can be used indoors
High abrasion resistance, low wear
Flexible and impact resistant
Can also be used on floors and walls
Suitable for use on uPVC
Gloss Level: Satin
Solids content in volume: 37 %
Heat Resistance: 90°C (dry heat), above 65°C discoloration may occur
Mixing Ratio: Base : Activator = 5.66 : 1 by volume
Drying Times At 20°C/RH 50%
Touch dry: 2 hours
Dry to handle: 4 hours
Dry to recoat: 24 hours
Fully cured: 2 days
Pot Life: 2 hours for a 5 litre mix at 20°C
Induction Time: 5 minutes
6,2 m²/l at 60 µm dry (depending on colour) for floors.
9,2 m²/l at 40 µm dry (depending on colour) for other applications.
Practical coverage depends on many factors such as porosity and roughness of the substrate and material losses during application.
Remove grease, oil and all other surface contamination using alkaline or high pressure (steam) cleaning in combination with appropriate detergents. Sand previous coatings that are in good condition to remove gloss and to roughen the surface slightly. Assure that the previous coating is compatible with the RUST-O-THANE 9200 by making a test application. Remove bad adhering coatings by scraping, wire brushing or sanding. (Spot)prime with commended Rust-Oleum or Mathys coatings. The surface must be clean and dry during application.
Max dry film thickness for floors: 75 µm dry, equals 200 µm wet. For walls: 60 µm dry, equals 160 µm wet.
For use on floors submitted to heavy abrasion, standard and medium colours are recommended. In case of deep and/or bright tones (red, yellow, orange, green, blue etc), it is advised to apply a clear topcoat.
The product is not recommended in case of stagnating water and/or immersion
Now also available in convenient 1 litre packaging. Ideal for smaller projects the new convenient 2-component packaging provides the base and activator in one convenient kit and the activator is supplied with a user-friendly spout cap.
Please contact Rawlins Paints` Technical Support Team on 0113 2455450 for more information.
Water / Solvent Based
Ultra-Low (5-49 g/l)
Single, Two or Three Pack
Brush, Roller, Spray
Dry to Handle (at 20°C)
Dry to Recoat (at 20°C)
Fully Cured (at 20°C)
6.2-9.2m² per litre
Max. Application Temperature
Min. Application Temperature
Solids by Volume
Heat Resistance (up-to)
90°C (dry heat), above 65°C discoloration may occur
Shelf Life (from date of manufacture)
Base 2 years and activator 1 year from the date of production in unopened cans, if stored in dry, well-ventilated and frost-free areas, not in direct sunlight at temperatures between 5° and 35° C. Opened activator cans must be used within 1 week.
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Rust-Oleum 9200 Rust-O-Thane Clear - CLEARANCE is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
Floor Application Kit from Rawlins Paints provides all the application equipment needed to apply conventional floor paints and coatings to a professional standard. The application of floor coatings is often crucial to their performance, so it is important to use the right tools to ensure a lasting finish.
Each kit contains:
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3).
Please click here for important information about these kits.
SET 1 (Hand Tools)
1 x Rust-Oleum...