Jotun Tankguard Plus is a two component polyamine cured novolac epoxy coating that has high resistance to most sour crude oils and a wide range of chemicals and solvents. It has outstanding chemical resistance to crude oil at temperatures up to 160°C. Jotun Tankguard Plus can be used as a primer, mid coat or finish coat in atmospheric and immersed environments.
Jotun Tankguard Plus is a two component polyamine cured novolac epoxy coating that has high resistance to most sour crude oils and a wide range of chemicals and solvents. It has outstanding chemical resistance to crude oil at temperatures up to 160°C. Jotun Tankguard Plus can be used as a primer, mid coat or finish coat in atmospheric and immersed environments on properly prepared carbon steel, galvanised steel, stainless steel and concrete substrates.
Jotun Tankguard Plus is specially designed as an internal lining for offshore, onshore and buried tanks and pipes such as chemical storage, waste water, grey water, process water, concrete bund, fire service lines and drilling mud tanks. This coating has very good resistance to high temperature products. Refer to Protective Product Resistance List.
Approvals and certificates
Additional certificates and approvals may be available on request.
Features & Benefits
BUYER NOTICE: Due to the complexities and risks within tank coatings, Jotun do not support the purchase of their Tankguard range through dealer/distributor channels. Jotun are happy to support with advice and documentation required for these types of coating projects but as they are removed from the end user the ability to control all risks involved with a coating project for a tank is limited. For these reasons, Jotun will only ensure the product quality within the can when Tankguard products are purchased via a distributor such as ourselves.
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Jotun Thinner No. 23 is a paint thinner designed to improve the flow of Jotun Tankguard epoxy products. It can also be used as a cleaner of pumps and tools after and before painting. Jotun Thinner No. 23 is specially suitable as a thinner for tankguard epoxy products.
• These colour samples are to be used for guidance only.
• Product contained within is generic to provide a close representation to your chosen colour.
• Should not be used to carry out any painting project, this is for colour selection purposes only and does not remove the need for you to ensure the correct product is chosen and tested for your application once a colour has been decided on.
• It is not a sample of the product you intend to purchase/use and cannot be used to test anything other than colour appearance.
• Notwithstanding any other provision of our conditions of sale, you agree and understand that many factors affect the colour of a painted product, including lighting, sheen level, method of application, batches variances number of coats and substrate surface.
• We cannot therefore promise that the colour of the product you ultimately purchase will exactly match the colour of this colour sample.
• Once you have selected a colour, you must purchase the smallest amount of the product you intend to use in your chosen colour and apply to a small, inconspicuous test area to be sure that it meets your expectations.
• Leave the product for 24 hours and then only buy more paint and/or apply more paint if you are completely happy with the results on the test area.
• We cannot be liable to you for any loss or damage if you have not complied with this process.
• Notwithstanding any other provision of our conditions of sale, you agree and understand that many factors affect the colour of a painted product, including lighting, sheen level, method of application and product surface.
• We cannot therefore promise that the colour of the product you paint with the Kolorbond paint will exactly match the colour of the item you send to us.
• You must therefore purchase the smallest Kolorbond paint pot available first and then apply the paint to a small, and where possible hidden, test area of your product to be sure that it meets your expectations.
• Leave the product for 24 hours and then only buy more paint and/or apply more paint to your product if you are completely happy with the results on the test area.
• We cannot be liable to you for any loss or damage if you have not complied with this process.
