• Sherwin-Williams Fast Clad ER

Sherwin-Williams Fast Clad ER

E130
SHE2146

Sherwin-Williams Fast Clad ER is a solvent-free, epoxy tank lining that offers superior flexibility, excellent edge retention, film forming and high build properties. Fast Clad ER enables ultra fast return to service in as little as 24 hours.

  • One coat protection
  • Fast return to service
  • Low VOC
  • Low odour
  • Dry to walk-on within four hours
  • Designed for plural-component application equipment
  • Greater than 70% edge retention
  • Low Temperature application and cure capabilities to 2°C
  • Please Note: This product is available as POA made to order subject to a minimum order quantity and an extended lead time of approximately 8-12 weeks
  • Please contact our sales team on 0113 2455450 or send a message to [email protected] for pricing information and to place an order

Colour
Pick a Colour
  • Current colour: White
Close colour picker
  • White
  • Black
  • Blue OAP
  • Haze Grey
Size
Finish
Quantity
Product not available
This Product is Price on Application Only

Description

Please Note: This product is available as POA made to order subject to a minimum order quantity and an extended lead time of approximately 8-12 weeks.

Please contact our sales team on 0113 2455450 or send a message to [email protected] for pricing information and to place an order.

Sherwin-Williams Fast Clad ER is a solvent-free, epoxy tank lining that offers superior flexibility, excellent edge retention, film forming and high build properties. Fast Clad ER enables ultra fast return to service in as little as 24 hours.

Features & Benefits

  • One coat protection
  • Fast return to service
  • Low VOC
  • Low odour
  • Dry to walk-on within four hours
  • Designed for plural-component application equipment
  • Greater than 70% edge retention
  • Low Temperature application and cure capabilities to 2°C

Recommended Uses

  • For use over prepared steel or masonry  surfaces in industrial and marine exposures such as:
  • Ballast tank interiors and oil storage tank interiors
  • Fuel storage tanks and external pipeline coating
  • Primary or Secondary containment
  • Acceptable for use with cathodic protection systems
  • Where rapid return to service and edge protection film build properties are required
  • Meets MIL-PRF-23236 Type VII, Class 5, 7, 5/18, 7/18, 13/18, 17, 17/18 Grade C requirements for single and multi-coat seawater, fuel, bilges, and CHT tanks
  • Blue OAP contains fluorescent pigment
  • Wind tower gearbox lining and transformer lining up to 140°C

Performance Tips

When using spray application, use a 50% overlap with each pass of the gun to avoid holidays, bare areas, and pinholes. If necessary, cross-coat spray at a right angle.

Spreading rates are calculated on volume solids and do not include an application loss factor due to surface profile, roughness or porosity of the surface, skill and technique of the applicator, method of application, various surface irregularities, material lost during mixing, spillage, overthinning, climatic conditions, and excessive film build. No reduction of material is recommended as this can affect film build, appearance, and adhesion.

Stripe coat all crevices, welds, and sharp angles to prevent early failure in these areas. Do not mix previously mixed material with new. Do not apply the material beyond recommended pot life.

Remove and solvent clean tip housing every 20-30 minutes.

For Immersion Service: (if required) Holiday test in accordance with ASTM D5162.
Guidance on techniques and required equipment to inspect a coating system incorporating Opti-Check OAP Technology can be found in SSPC-TU 11.

Refer to Product Information sheet for additional performance characteristics and properties. 

Product Details
E130

Data sheet

Manufacturer
Sherwin-Williams
For Use On
Steel, Masonry
Application Method
Brush, Roller, Spray
Sheen
Gloss
Colour
Standard / Ready Mixed
VOC Levels
Low (50-149 g/l)
Single, Two or Three Pack
Two-Pack
Pack Size
20L
Application
Brush, Roller, Spray
Coverage
1.8 - 2.2m² per litre
Solids by Volume
98%, ± 2%, mixed
UN Number (Activator)
UN3082
UN Number (Base)
UN3066
Solids by Weight
98%, ± 2%, mixed
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


questions Fredvenable on 2023-01-19 14:49:33
Question: 

What is the maximum Rico time on fast clatter

Answer from Rawlins’ Technical Team: 

We are unsure what you mean by fast clatter, but in regards to drying times to recoat at 4.5°c the minimum drying time 6 hours, the maximum drying time is 14 days.

Further information for preparation and application is in the Product Data Sheet, this can be found in the data sheets tab on the product page.


Question about the product

* Required fields
(read)
Send