Sherwin-Williams Epo-Phen FF
  • Sherwin-Williams Epo-Phen FF

Sherwin-Williams Epo-Phen FF

Epo-Phen FF

Sherwin-Williams Epo-Phen FF coating is a flake-filled (MIO) amine cured epoxy phenolic novolac formulated for use under thermal insulation at elevated or cryogenic temperatures and for immersion service in water and hydrocarbons such as gasoline, fuel oil, and diesel fuel. 

  • Temperature resistant to 218°C (425°F), constant;  232°C (450°F) intermittent (dry service)
  • Self priming
  • Chemical resistant

**Available for delivery - see Delivery Options below**

Colour
Size
Finish
£96.23
VAT excluded

£115.47 Tax incl.
Quantity

Description

Sherwin-Williams Epo-Phen FF coating is a flake-filled (MIO) amine cured epoxy phenolic novolac formulated for use under thermal insulation at elevated or cryogenic temperatures and for immersion service in water and hydrocarbons such as gasoline, fuel oil, and diesel fuel. 

Features & Benefits

  • Temperature resistant to 218°C (425°F), constant;  232°C (450°F) intermittent (dry service)
  • Self priming
  • Chemical resistant

The micaceous iron oxide (MIO) provides:

  • High temperature resistance
  • Film reinforcement
  • One coat, high build application
  • Improved edge protection

Recommended Uses

  • Steel and stainless steel tanks and piping under insulation
  • Non-insulated structural steel and piping subjected to chemical or abrasion attack
  • Use in areas subject to wet/dry cycling up to 149°C (300°F)
  • Use in areas where temperature resistance up to 232°C (450°F) is required (dry service)
  • Acceptable for use in immersion service at elevated temperatures for fresh water and distilled water 99°C (210°F)
  • Suitable for storage of gasoline, fuel oil, diesel fuel, and other similar hydrocarbon cargos
  • Not qualified for potable water immersion
  • Water and wastewater facilities
  • Wind tower gearbox lining

Performance Tips

Stripe coat crevices, welds, and sharp angles to prevent early failure in these areas.

When using spray application, use a 50% overlap with each pass of the gun to avoid holidays, bare areas, and pinholes. If necessary, cross spray at a right angle.

Spreading rates are calculated on volume solids and do not include an application loss factor due to surface profile, roughness or porosity of the surface, skill and technique of the applicator, method of application, various surface irregularities, material lost during mixing, spillage, overthinning, climatic conditions, and excessive film build.

For Immersion Service: (if required) Holiday test in accordance with ASTM D5162 for steel, or ASTM D4787 for concrete.

Excessive reduction of material can affect film build, appearance, and adhesion.

Do not mix previously catalyzed material with new.

Do not apply the material beyond recommended pot life. In order to avoid blockage of spray equipment, clean equipment before use or before periods of extended downtime with Reducer #15.

Temperatures above 25°C (77°F) will shorten the pot life.

Do not apply over 225 microns (9.0 mils) total dft when used in service above 149°C (300°F).

Not recommended for potable water immersion.

Acceptable for insulation to be applied over the coating, after the coating has reached it's dry to touch time.

Refer to Product Information sheet for additional performance characteristics and properties.

Product Details
Epo-Phen FF

Data sheet

Manufacturer
Sherwin-Williams
For Use On
Steel
Application Method
Brush, Roller, Spray
Sheen
Semi Gloss
Colour
Standard / Ready Mixed
Single, Two or Three Pack
Two-Pack
Pack Size
5L, 20L
Application
Brush, Roller, Spray
Coverage
3.0 - 3.9m² per litre
Solids by Volume
70% ± 2%
Shelf Life (from date of manufacture)
24 months, unopened Store indoors at 4.5°C (40°F) to 38°C (100°F)
Touch Dry
3 hours
UN Number (Activator)
UN3066
UN Number (Base)
UN1263
Fully Cured
7 days
Solids by Weight
85% ± 2%
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


questions NEP services on 2020-06-05 08:23:27
Question: 

Good morning, is this product two pack, if so do you gert both components when ordering the 20L option.

Answer: 

Yes this is a two pack product and both components are including product listing and pricing.

questions Ray Manley on 2018-11-14 20:41:10
Question: 

Is this product rated for aluminum materials? tubing/piping/ angle etc.

Answer: 

Sherwin-Williams Epo-Phen FF can indeed be applied to aluminium, you can download the product data sheets from the product page for further details.


Question about the product

* Required fields
(read)
Send