Sherwin-Williams Macropoxy P300
  • Sherwin-Williams Macropoxy P300

Sherwin-Williams Macropoxy P300

P300

Sherwin-Williams Macropoxy P300, formerly known is Waterline P300, is a solvent free two-pack epoxy water resistant finish for use on the internal surfaces of potable water pipes and tanks.

Colour
Size
Finish
£483.37
VAT excluded

£580.04 Tax incl.
Quantity

Description

Sherwin-Williams Macropoxy P300, formerly known is Waterline P300, is a solvent free two-pack epoxy water resistant finish for use on the internal surfaces of potable water pipes and tanks.

Endorsements

  • DWI approved as a site and factory applied coating for potable water retaining structures ref DWI 56.4.253
  • Water Industry Act 1991 : Section 69
  • Water Supply (Water Quality) Regulations : 1989
  • Water Supply (Water Quality) Regulations (Amendment) 1991 - Regulation 25(1)
  • Water Regulations Advisory Scheme Directory Reference 0512526

Recommended Topcoats

Macropoxy P300 is only recommended to be overcoated for touch up purposes.
Prior to overcoating, these areas must be thoroughly abraded, then solvent washed using Cleanser Thinners No. 13. Allow all solvent washings to dry, and thoroughly ventilate the area before applying touch up coat. 

Surface Preparation

For tank internals and for maintenance of existing tanks, blast clean to Sa21⁄2 BS EN ISO 8501-1:2007 using angular grit. Minimum surface profile 75 microns.
Ensure surfaces to be coated are clean, dry and free from all surface contamination. 

Application Conditions & Overcoating

Macropoxy P300 should preferably be applied at tempera- tures in excess of 10°C. Relative humidity should not exceed 85% and in these conditions good ventilation is essential. The use of dehumidifiers to maintain stable environmental condition is recommended during application and curing

of the coating. Substrate temperature shall be at least 3°C above the dew point and always above 0°C.

At application temperatures below 10°C, drying and curing times will be significantly extended.

Return to Service : Applied coating must be allowed to cure for 16 hours at 3°C or above before returning to service. Should ambient temperature fall below 3°C in this 16 hour period, a further 16 hours should be allowed, once the ambient temperature rises above 3°C.

If it is desired to overcoat outside the times stated on the data sheet, please seek advice of Technical Team. 

It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.

Product Details
P300

Data sheet

Typical Coverage (per coat)
2.00m² per litre
Touch Dry
1.5 Hours
Application
Brush, Spray
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


questions Tony Leyland on 25/10/2018
Question: 

Hi, is a primer recommended forSherwin-Williams Macropoxy P300 on steel the has been blast cleaned to SA2.5?

Answer: 

After recommended preparation, no primers are required or recommended, Sherwin-Williams Macropoxy P300 is used directly to the blasted steel.

questions Colin Spruce on 14/09/2017
Question: re Macropoxy P300 paint, is this suitable for a lime slurry of PH 12.5 value Regards
Answer: 

Sherwin-Williams Macropoxy P300 would not be suitable. Lime slurry (calcium hydroxide) would require an epoxy phenolic at a minimum, Sherwin-Williams Epo-Phen FF can withstand up to 50% at 60°C.


Question about the product

* Required fields
(read)
Send
16 other products in the same category:

Jotun Balloxy HB Light WG

Jotun Balloxy HB Light WG is a 'Wintergrade' version of Jotamastic 90 to aid application in lower temperatures and to provide faster drying and curing times. Jotun Balloxy HB Light WG is a surface tolerant, high solids, high build epoxy mastic coating for water ballast tanks. It is specially designed for areas where optimum surface preparation is not...

Price £140.80
In stock

International Interline 850

International Interline 850 is a two component, chemically resistant, high solids, high build epoxy phenolic tank and pipe lining coating to provide corrosion protection for the internals of steel storage tanks and pipes containing a range of products.

Price £576.24
In stock

Sherwin-Williams Nova-Plate 325

Nova-Plate 325 is an amine cured, glass and ceramic filled tank lining that utilises advanced epoxy novolac technology. It is engineered to protect cargo and steel tank interiors from chemicals stored at high temperatures and high pressures. It provides quick return to service, high film build and can be used in applications where conventional...

Price £196.17
In stock

Jotun Tankguard Zinc

Jotun Tankguard Zinc is a two component moisture cured inorganic zinc ethyl silicate coating that is a specially designed tank coating and lining with excellent cargo resistance. To be used as a single coat system only, in atmospheric and immersed environments. Suitable for properly prepared carbon steel substrates.

Price £244.39
In stock

Jotun Tankguard SF

Jotun Tankguard SF is a two component solvent free amine cured novolac epoxy coating that is a specially designed tank lining with very good chemical resistance. It can be used as a primer, mid coat or finish coat in atmospheric and immersed environments. Suitable for properly prepared carbon steel, galvanised steel, stainless steel and concrete substrates.

Price £286.14
In stock

International Interline 975

International Interline 975 is a two component, solvent free, heavy duty epoxy tank lining for application to steel tank internals to provide corrosion resistance to a range of products including crude oil, white oils and potable water.

Price £412.78
In stock

Jotun Tankguard 412

Jotun Tankguard 412 is a two component solvent free polyamine cured epoxy coating that is a general purpose tank lining with good chemical resistance. It can be used as a primer, mid coat or finish coat in atmospheric and immersed environments. Suitable for properly prepared carbon steel, galvanised steel, stainless steel and concrete substrates.

Price £168.74
In stock

International Interline 984

International Interline 984 is a versatile epoxy phenolic tanklining, that is a solvent-free, epoxy phenolic lining system, applied in a single coat, offering chemical resistance in a wide range of applications.

Price £542.96
In stock

Sherwin-Williams Fast Clad ER

Sherwin-Williams Fast Clad ER is a solvent-free, epoxy tank lining that offers superior flexibility, excellent edge retention, film forming and high build properties. Fast Clad ER enables ultra fast return to service in as little as 24 hours.

Price £337.99
In stock

Carboline Rustbond FC

A cross-linked penetrating metal primer/sealer with excellent wetting properties. It is highly flexible with good chemical and solvent resistance, and accepts a variety of topcoats. Top Features Universal primer and tie-coat Cures down to 35°F (2°C) Low stress, highly flexible film Extremely high solids Contains corrosion inhibitors

Price £89.63
In stock

Sherwin-Williams Macropoxy P100

Sherwin-Williams Macropoxy P100, formerly known as Pipegard P100, is a high build 2-pack polyamide cured epoxy zinc phosphate primer/finish. Macropoxy P100 is used as an internal flow coating for pipelines.

Price £287.82
In stock

International Interline 399

International Interline 399 is a high performance, highly crosslinked two component epoxy novolac tank lining, with excellent heat and solvent resistance suitable for internal lining of storage vessels and process vessels at elevated temperatures up to 130°C (266°F).

Price £596.16
In stock

Sikalastic 841 ST

Sikalastic 841 ST is a liquid applied, pure polyurea membrane. Sikalastic 841 ST is a two part, elastic, 100% solids, very fast curing pure polyurea liquid applied membrane with very good chemical resistance. Sikalastic 841 ST shall not be used in closed structures containing biogenic sulphuric acid. Sikalastic 841 ST can only be spray applied with...

Price £5,742.31
In stock

Jotun Jotamastic SF

Jotun Jotamastic SF is a two component polyamine cured epoxy mastic coating that is a surface tolerant, solvent free, high build product. Well suited for early immersion and specially designed for areas where optimum surface preparation is not possible or desired. Provides long lasting protection in environments with high corrosivity.

Price £155.70
In stock

Jotun Balloxy HB Light

Jotun Balloxy HB Light is a surface tolerant, high solids, high build epoxy mastic coating for water ballast tanks. It is specially designed for areas where optimum surface preparation is not possible or desired and provides long lasting protection in environments with high corrosivity. Jotun Balloxy HB Light can be used as primer, mid coat or finish coat...

Price £126.68
In stock

Jotun Jotamastic SF Alu

Jotun Jotamastic SF Alu is a two component polyamine cured epoxy mastic coating aluminium pigmented to provide a metallic silvery finish that is a surface tolerant, solvent free, high build product well suited for early immersion. Specially designed for areas where optimum surface preparation is not possible or desired.

Price £155.70
In stock