PPG Thinner 90-53
This thinner has been developed by PPG Protective and Marine Coatings for use with selected paint products.More Information Delivery Info
PPG PhenGuard 935 is a two-component, high-build, amine adduct-cured novolac phenolic epoxy coating, developed as the second coat in the Phenguard tank coating system. Offers excellent resistance to a wide range of organic acids, alcohols, edible oils, solvents and fats (regardless of free fatty acid content).
PPG PhenGuard 935 is a two-component, high-build, amine adduct-cured novolac phenolic epoxy coating, developed as the second coat in the Phenguard tank coating system. Offers excellent resistance to a wide range of organic acids, alcohols, edible oils, solvents and fats (regardless of free fatty acid content).
PhenGuard 935 has good application properties, resulting in a smooth surface, and is a recognized corrosion control coating (Lloyd's register).
Basic data at 20°C (68°F)
Data for Mixed Product | |
---|---|
Mass density | 1.7 kg/l (14.2 lb/US gal) |
Volume solids | 66 ± 2% |
VOC (Supplied) | Directive 1999/13/EC, SED: max. 191.0 g/kg |
max. 315.0 g/l (approx. 2.6 lb/US gal) | |
Recommended dry film thickness | 100 µm (4.0 mils) |
Theoretical spreading rate | 6.6 m²/l for 100 µm (265 ft²/US gal for 4.0 mils) |
Overcoating Interval | Minimum: 24 hours |
Maximum: 21 days | |
Dry to touch | 2 hours |
Full Cure | See Cure table further below |
Notes:
Recommended Substrate Conditions & Temperatures
Substrate conditions
Substrate Temperature & Application Conditions
System Specification
Instructions For Use
Mixing ratio by volume: base to hardener 88:12
Induction time
Allow induction time before use
Mixed product induction time | |
---|---|
Mixed product temperature | Induction time |
15°C (59°F) | 20 minutes |
20°C (68°F) | 15 minutes |
25°C (77°F) | 10 minutes |
Application
Air spray
Recommended Thinner
Volume of thinner
Nozzle orifice
Nozzle pressure
Airless spray
Recommended Thinner
Volume of thinner
Nozzle orifice
Nozzle pressure
Brush
Recommended Thinner
Volume of thinner
Cleaning solvent
Note: Maximum DFT when brushing: 60 µm (2.4 mils)
Spreading rate and film thickness | |
---|---|
DFT | Theoretical spreading rate |
100 µm (4.0 mils) | 6.6 m²/l (265 ft²/US gal) |
125 µm (5.0 mils) | 5.3 m²/l (212 ft²/US gal) |
Overcoating interval for DFT up to 100 µm (4.0 mils) | ||||||
---|---|---|---|---|---|---|
Overcoating with... | Interval | 10°C (50°F) | 15°C (59°F) | 20°C (68°F) | 30°C (86°F) | 40°C (104°F) |
itself and PHENGUARD 940 | Minimum | 36 hours | 32 hours | 24 hours | 16 hours | 12 hours |
Maximum | 28 days | 25 days | 21 days | 14 days | 7 days |
Notes:
Curing time for DFT up to 150 µm (6.0 mils) | |
---|---|
Substrate temperature | Minimum curing time before transport of cargoes without note 4, 7, 8 or 11 and ballast water or tank test with sea water |
10°C (50°F) | 14 days |
15°C (59°F) | 14 days |
20°C (68°F) | 10 days |
30°C (86°F) | 7 days |
40°C (104°F) | 5 days |
Notes:
Pot life (at application viscosity) | |
---|---|
Mixed product temperature | Pot life |
10°C (50°F) | 6 hours |
20°C (68°F) | 4 hours |
30°C (86°F) | 1.5 hours |
Safety Precautions
This is a solvent-borne paint and care should be taken to avoid inhalation of spray mist or vapor, as well as contact between the wet paint and exposed skin or eyes
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
PPG PhenGuard 935 is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
This thinner has been developed by PPG Protective and Marine Coatings for use with selected paint products.More Information Delivery Info
This thinner has been developed by PPG Protective and Marine Coatings for use with selected paint products.More Information Delivery Info
We no longer stock this product, but can recommend PPG PhenGuard 985 as a great alternative. Please note: it is important to check that any alternative product is suitable for your requirements, as our suggestion is given in good faith but without warranty. If you are in any doubt please first contact our technical team on 0113 2455450...
PPG PhenGuard 940 is a two-component, high-build, amine adduct-cured novolac phenolic epoxy finish; the final coat in the Phenguard tank coating system, with excellent resistance to a wide range of acids, alcohols, edible oils, solvents and fats (regardless of free fatty acid content).Final coat in the PHENGUARD tank coating system:...