PPG Thinner 90-53
This thinner has been developed by PPG Protective and Marine Coatings for use with selected paint products.More Information Delivery Info
We no longer stock this product; please contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to find an alternative product.
PPG SigmaGuard 730, a two-component, high solids polyamine cured phenolic epoxy coating for tanks with good chemical resistance against a wide range of chemicals that can be used under insulation up to 150°C (300°F). The coating has short curing periods, down to low temperatures.
Please note: This product is subject to a minimum order quantity of 440L and has an approximate delivery lead time of 21-28 days
Reference | Colour | Size | Gloss Level |
---|---|---|---|
247818 | Off White | 20 litres | Gloss |
247817 | Cream | 20 litres | Gloss |
Two-component, high solids polyamine cured phenolic epoxy coating.
Data for mixed product at 20°C (68°F) | |
---|---|
Number of components | Two |
Mass density | 1.4 kg/l (11.7 lb/US gal) |
Volume solids | 78 ± 2% |
VOC (Supplied) | Directive 1999/13/EC, SED: max. 169.0 g/kg |
max. 242.0 g/l (approx. 2.0 lb/US gal) | |
Recommended dry film thickness | 150 µm (6.0 mils) |
Theoretical spreading rate | 5.2 m²/l for 150 µm (209 ft²/US gal for 6.0 mils) |
Pot life | 1.5 hours at 20°C (68°F) |
Dry to touch | 3 hours |
Overcoating Interval | Minimum: 8 hours |
Maximum: 28 days | |
Full cure after | See table further below |
Shelf life | Base: at least 12 months when stored cool and dry |
Hardener: at least 24 months when stored cool and dry |
Notes:
Recommended Substrate Conditions and Temperatures
Substrate conditions
Substrate Temperature & Application Conditions
Instructions for Use
Mixing ratio by volume: base to hardener 75:25 (3:1)
Induction Time
Allow induction time before use
Mixed product induction time | |
---|---|
Mixed product temperature | Induction time |
15°C (59°F) | 15 minutes |
20°C (68°F) | 10 minutes |
25°C (77°F) | 5 minutes |
Air spray
Recommended thinner
Volume of thinner
Nozzle orifice
Nozzle pressure
Airless Spray
Recommended thinner
Volume of thinner
Nozzle orifice
Nozzle pressure
Brush/roller
Cleaning Solvent
DFT | Theoretical spreading rate |
---|---|
125 µm (5.0 mils) | 6.2 m²/l (250 ft²/US gal) |
150 µm (6.0 mils) | 5.2 m²/l (209 ft²/US gal) |
Note:
Overcoating interval for DFT up to 150 µm (6.0 mils)
Overcoating with... | Interval | 5°C (41°F) | 10°C (50°F) | 20°C (68°F) | 30°C (86°F) | 40°C (104°F) |
---|---|---|---|---|---|---|
Itself | Minimum | 32 hours | 24 hours | 8 hours | 4 hours | 3 hours |
Maximum | 28 days | 28 days | 28 days | 14 days | 7 days |
Notes:
Curing time for DFT up to 150 μm (6.0 mils)
Substrate temperature | Minimum curing time before transport of aliphatic petroleum products and ballast water and tanktest with seawater | Minimum curing time before transport of cargoes without note 4, 7, 8 or 11 |
---|---|---|
5°C (41°F) | 10 days | 17 days |
10°C (50°F) | 7 days | 14 days |
20°C (68°F) | 3 days | 5 days |
30°C (86°F) | 60 hours | 4 days |
40°C (104°F) | 36 hours | 3 days |
Notes:
Pot Life (at application viscosity)
Mixed product temperature | Pot life |
---|---|
15°C (59°F) | 3 hours |
20°C (68°F) | 1.5 hours |
25°C (77°F) | 1 hour |
30°C (86°F) | 30 minutes |
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
PPG SigmaGuard 730 is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
This thinner has been developed by PPG Protective and Marine Coatings for use with selected paint products.More Information Delivery Info
This thinner has been developed by PPG Protective and Marine Coatings for use with selected paint products.More Information Delivery Info