HMG Pre Cat AV Colours is a fast drying 1K lacquer with good film build and excellent application characteristics.
Please note: Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour.
HMG Pre Cat AV Colours is a fast drying 1K lacquer with good film build and excellent application characteristics. Available in a range of coloured sheen finishes.
| Technical Data | |
|---|---|
| Volume Solids: | 31.4% |
| VOC Content: | 0.7kgs/ltr |
| SG: | - |
| Viscosity: | - |
| Density: | 0.955 g/cm³ |
| Storage Conditions: | Store between 5°C - 25°C. When not in use, cans must be kept sealed. |
| Shelf Life: | 12 months from delivery date in original sealed containers. |
| Flash Point: | - 4°C |
| Product Data | |||
|---|---|---|---|
| Dry Film Thickness | Wet Film Thickness | ||
| Compliant Spray Gun: | 25 μm | 70g/m² μm | |
| Pressure Pot: | 25 μm | 70g/m² μm | |
Coverage: 10 square metres per litre @ 25 microns dft (theoretical)
| Drying Times At 20°C | |
|---|---|
| Touch Dry: | 10 minutes |
| Dry To Recoat: | 10 minutes minimum, 6 hours maximum |
| Fully Cured: | 60 minutes |
| Technical Data | |||||
|---|---|---|---|---|---|
| Compliant Spray Gun | Pressure Pot | ||||
| Mixing Ratio: | Ready for use | Ready for use | |||
| - | - | ||||
| Thinner Options: | n/a | n/a | |||
| - | - | ||||
| Viscosity: | 30 - 35 seconds B4 cup | 30 - 35 seconds B4 cup | |||
| Spray Gun Setup: | 1.4 - 1.6 | 1.2 - 1.4 | |||
| Number Of Coats (Guide Only): | 2 - 3 coats | 2 - 3 coats | |||
| Flash Off: | 10 minutes between coats | 10 minutes between coats | |||
For further information on mixing ratios please contact Rawlins Paints on Tech - 0113 2455450 (option 2) or [email protected] Sales - 0113 2455450 or [email protected]
| Information on basic physical and chemical properties | |
|---|---|
| Form: | Liquid |
| Colour: | According to product specification |
| Odour: | Characteristic |
| Odour Threshold: | Not determined |
| pH-value: | Not determined |
| Change in Condition | |
| Melting point/freezing point: | Undetermined |
| Initial boiling point and boiling range: | 76.8°C |
| Flash Point: | - 4°C |
| Flammability (solid, gas): | Not applicable |
| Ignition temperature: | 315°C |
| Decomposition temperature: | Not determined. |
| Auto-ignition temperature: | Product is not selfigniting |
| Explosive properties: | "Product is not explosive. However, formation of explosive air vapour mixtures are possible." |
| Explosion limits: Lower: | 1.2 Vol % |
| Explosion limits: Upper: | 12 Vl % |
| Vapour pressure at 20°C: | 100 hPa |
| Density at 20°C: | 0.955 g/cm³ |
| Relative density: | Not determined |
| Vapour density: | Not determined |
| Evaporation rate: | Not determined |
| Solubility in / Miscibility with water: | NOT MISCIBLE |
| Partition coefficient: n-octanol/water: | Not determined |
| Viscosity: Dynamic at 20°C: | Not determined |
| Viscosity: Kinematic: | 23 s (DIN 53211/4) |
| Solvent content: Organic solvents: | 71.5% |
| Solids content: | 31.4% |
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
 Richard Semple on 2023-09-03 17:11:52 | Question: Been asked to finish a pine dining table and 10 accompanying chairs in a dark chocolate brown. The table will be paint stripped and sanded back. Would this be a good product for the job. Would I need a base coat on first. Looking at a satin finish please advise many thanks |
Answer from Rawlins’ Technical Team: This product would be fine as a finish coat. Assuming you have a clean, dry, sound surface that has been sanded prior to application, HMG Pre Cat Standard Sealer would be recommended as a basecoat/sealer, prior to finishing with HMG Pre Cat AV Colours. This product is available in 5000+ RAL, BS & NCS Colours to a Satin, Matt or Gloss finish. | |
| Neil on 2022-10-04 10:18:26 | Question: Im looking to paint over sealed mdf would this paint require an additional primer |
Answer from Rawlins’ Technical Team: We would recommend testing for compatibility and adhesion prior to full application on a small area with the previously sealed mdf. For bare mdf the primer to use would be HMG Pre Cat Primefast 2014-04. | |
| Daniel on 2021-10-22 17:08:10 | Question: Hello, what is the guarantee in terms of fading and longevity, with proper preparation and using the pre cat primer? |
Answer from Rawlins’ Technical Team: I'm afraid no warranties or guarantees are offered with this product. | |
HMG Pre Cat AV Colours is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
HMG Pre Cat MDF Sealer is a high solids, clear, 1K primer/sealer for use on MDF.Fast drying Superb filling properties Ease of application Excellent sandabilityMore Information Delivery Info
£60.19 (incl. VAT)
£50.16 (ex. VAT)
HMG Pre Cat Standard Sealer is a 1K basecoat/sealer for use on wood and veneer.Fast drying. Contains no sterate. Excellent and easy sandability. Gives excellent and tenacious adhesion to wood with minimal preparation. Minimises sinkage of topcoats. Enables fast throughput of work to a high standard.More Information Delivery Info...
£208.67 (incl. VAT)
£173.89 (ex. VAT)
We no longer stock this product, but can recommend HMG M99 Cellulose Aerosol as a great alternative. Please note: it is important to check that any alternative product is suitable for your requirements, as our suggestion is given in good faith but without warranty. If you are in any doubt please first contact our technical team on 0113...
