SikaBond Wood Floor Installation Kit is a complete kit to fit up to 20m² of wood flooring. The kit contains: 10 x 600ml Sausages, bulk gun and 2 x reuseable precut nozzles.
SikaBond Wood Floor Installation Kit is a complete kit to fit up to 20m² of wood flooring. The kit contains: 10 x 600ml SikaBond MS Wood Floor adhesive foils, 10 x 600ml Sausages, bulk gun and 2 x reuseable precut nozzles. SikaBond MS Wood Floor is a high quality adhesive that is ideal for bonding wood floors to all common substrates. It is permanently elastic to accommodate differential movement caused by changes in humidity and climatic conditions. SikaBond Wood Floor Installation Kit is suitable for use with underfloor heating systems.
Please ensure substrate is dry and suitable to receive a wooden floor. If in doubt use Sika Primer MB or SikaBond Rapid DPM.
Concrete / cement screed: Must have an open texture, be dry and thoroughly cleaned with industrial vacuum cleaner.
Anhydrite screed / Calcium Sulphate screed: Must be completely dry, ground and thoroughly cleaned with an industrial vacuum cleaner shortly before bonding starts. NOTE: Not to be used in conjunction with damp proof membranes.
Broadcast mastic asphalt: Must be primed with Sika Primer MB or SikaBond Rapid DPM (see local Data Sheets for application instructions).
Glazed ceramic and old ceramic tiles: Degrease, clean with Sika Remover 208 or grind the tile-surface and clean thoroughly with an industrial vacuum cleaner.
Wood / gypsum boards (e.g. chipboards, plywood): Glue / screw the boards to the substructure. They have to be fixed on the substrate. In the case of floating subfloors, please contact our Technical Department.
Unknown substrates: Please contact Rawlins Paints' Technical Support Team on 0113 2455450 (option 2) or send a message to [email protected] for more information.
SikaBond MS Wood Floor Adhesive can be used without priming on cement floors, anhydrite floors, chip boards, concrete and ceramic tiles, steel access floors, plywood and most common substrates.
For broadcast mastic asphalt, cement floors with an excessive moisture content, as well in case of renovation on old adhesive residues and on structurally weak substrates use Sika Primer MB or SikaBond Rapid DPM (for detailed instructions consult Product Data Sheets).
Minimum screed requirements: 28 days maturing and max 3% moisture content before using this adhesive. For moisture contents at 3.1-7%, use in conjunction with a moisture barrier. Do not use this product above these recommended moisture levels.
METHOD 1 - Bead application
After the preparation of sausage and gun, extrude a triangular shaped bead of adhesive approximately 10 mm high and 8 mm wide at 100-250 mm centres (dependent on wood floor type) on the properly prepared subfloor. Press the wood floor elements firmly in to the adhesive (at right angles with adhesive beads). The elements can then be joined together using a hammer and an impact block. Ensure a perimeter gap of 20-15mm is maintained between walls and flooring.
METHOD 2 - Sika Silent Layer Mat application
Sika Silent Layer Mat application. Roll out the mat so the pre-cut slots are at 90˚ to the direction of the wood flooring. Gun adhesive into the slots ensuring all openings are filled with a triangular bead of adhesive 10mm high by 8mm wide. Place timber onto adhesive and mat. Use a block and mallet to close joints in wood floor as required. Allow to fully cure overnight. Fresh, uncured adhesive remaining on the wood floor surface must be removed immediately with a clean cloth and if necessary cleaned with Sika Remover 208. Test wood floor surfaces for compatibility with Sika Remover 208 before use. The laying instructions of the wood floor manufacturer as well as standard construction rules must be observed. After installation, allow adhesive to fully cure before replacing furniture, normally overnight.
Minimum wood sizes:
Length: Must go over at least 3 adhesive beads.
Width: >50mm
Thickness: 12-28mm (must not exceed 28mm).
Wood floors in non insulated areas such as basements, or other areas without a damp proof membrane, can only be installed after the application of Sikafloor EpoCem and Sika Primer MB or SikaBond Rapid DPM to control the moisture. For detailed instructions consult the Product Data Sheets or contact our Technical Department. In case of chemically pre-treated types of wood floors (e.g. ammonia, wood stain, timber preservative) and woods with high oil content, SikaBond MS Wood Floor Adhesive is only to be used after a written recommendation from our Technical Department.
DO NOT USE on PE, PP, TEFLON, and certain plasticised synthetic materials (carry out pre-trials or contact our Technical Department). Some primers can negatively influence the adhesion of SikaBond MS Wood Floor Adhesive (pre-trials recommended).
Covers up to 20m2 of wood flooring.
20 mins at 23°C and 50% RH. Floors can be walked on 24 hours after fixing.
Fresh, uncured adhesive remaining on the wood surface must be removed immediately and if necessary cleaned with Sika Remover 208. Test wood floor surfaces for compatibility with Sika Remover 208 before use. Cured adhesive may be removed from prefinished flooring using a suitable plastic scraper and/or pencil eraser.
All technical data stated in this Data Sheet are based on laboratory tests. Actual measured data may vary due to circumstances beyond our control.
For information and advice on the safe handling, storage and disposal of chemical products, users shall refer to the most recent Safety Data Sheet (SDS) containing physical, ecological, toxicological and other safety-related data.
Please contact Rawlins Paints' Technical Support Team on 0113 2455450 (option 2) or send a message to [email protected] for more information.
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
SikaBond Wood Floor Installation Kit is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
Sika Remover 208 can be used for removing traces of Sikaflex products from unwanted places and tools and it is also ideal to clean painted surfaces prior to bonding. Uses:Removes uncured excess material of Sikaflex adhesive or sealant from application tools or from soiled surfaces Pre-cleaning of strongly contaminated non-porous...
£25.66 (incl. VAT)
£21.38 (ex. VAT)
Sikafloor 81 EpoCem is a three part cement and epoxy combination mortar from Sikafloor for self-smoothing floor screeds of 1.5 to 3mm. Use as a Temporary Moisture Barrier (TMB) or under Epoxy, Polyurethane and PMMA resin floors, over high moisture content substrates, even green concrete. More Information Delivery Info
£136.96 (incl. VAT)
£114.13 (ex. VAT)
Sika Primer MB is a primer and moisture control coating for cementitious substrates prior to levelling or bonding with elastic sikabond adhesives. It is a one coat, 2-part, solvent free, low viscosity, epoxy resin primer for use in conjunction with Sika Schönox levelling compounds, dispersion primers and SikaBond Wood Floor adhesives....
£166.39 (incl. VAT)
£138.66 (ex. VAT)
Sika Silent Layer Mat is a high quality polyethylene foam mat available in two depths, 3mm and 5mm. Designed to reduce the sound of footsteps in areas of heavy foot flow. It is effective and easy to lay. Features and BenefitsReduce walking sound Wood floor bonded directly to subfloor No outwearing of mat Can be walked on during...
£170.89 (incl. VAT)
£142.41 (ex. VAT)
SikaBond Rapid DPM is a solvent free reaction curing resin primer and damp proof membrane for cement based substrates. Used for priming, consolidating and sealing of absorbent and non-absorbent sub-floors, consolidating weak cement screed and isolation of old adhesive residues. 1-part, ready to use. Rapid drying (approx 45 minutes at 50%...
£544.69 (incl. VAT)
£453.91 (ex. VAT)
