Remmers Induline GW-306 is a water-based primer with protection against soft rot and blue stain. Ready for use by dipping or flow-coating, it has excellent flow characteristics on untreated wood, good pore wetting performance, and outstanding (wet) adhesion.

Its range of uses includes:

• Wood outdoors which does not come into contact with the ground
• Soft and hard woods
• Dimensionally stable wood building elements: e.g. windows and doors
• Wood building elements with limited dimensional stability, e.g. folding shutters, matchboarding, summerhouses
• Wood building elements with no dimensional stability: e. g. fences, framework, carports, planking
• For use by professionals

Quick Links - Click To Jump To Section:

• Features & Benefits
• Application Rate
• Product Data
• Possible System Products
• Preparation
• Directions
• Tips on Use
• Tools / Cleaning
• Storage / Shelf Life

Features & Benefits

• Ready for use by dipping or flow-coating
• Excellent flow characteristics on untreated wood
• Good pore wetting performance
• Outstanding (wet) adhesion
• Protects against stain and blue rot

Application Rate

120 - 140 ml/m² per coat

Depending on the processing method, wood type and wood surface.

Product Data

• Binder: Special resins
• Density (20 °C): Approx. 1.015 - 1.13 g/cm³
• Viscosity (20 °C): Runout time approx. 24 - 26 s in ISO cup 3 mm
• Odour: Characteristic
• Preservative: IPBC (3-iodo-2-propynyl butylcarbamate)

The values stated represent typical characteristic data of the product and are not to be understood as binding product specifications.

Possible System Products

• Induline LW-700 (3400)
• Induline DW-601 Aqua Stop (1725)
• Induline ZW-400 (3900)

Preparation

Substrate requirements

The substrate must be clean, dry, free of dust, grease and loose substances, and prepared in the correct manner.

Dimensionally stable wood building elements: wood moisture content 11-15%

Wood building elements with limited or no dimensional stability: wood moisture content max. 18%

Directions

Conditions for use

Temperature of the material, air and substrate: +15 °C to +30 °C.

Processing conditions are between +15 °C and +30 °C at a relative humidity of 40 - 80%.

Stir well, including during application or after a break in work.

Qualified specialist companies: brushing, dipping, flow-coating and spraying in closed systems only.

Once dry, apply further coatings.

Seal opened containers well and use contents as soon as possible.

Tips on Use

Check colour, adhesion and compatibility with the substrate by setting up a trial area.

Substances in oak may bleed, causing dark discolouration, when coated with water dilutable dispersion stains.

Apply forced drying to tannin-containing woods.

The best flow results on Accoya, oak and chestnut are achieved at a pH value of 9.0–9.5, corresponding to an additive content of 0.3–0.5% VP 20829 Additive (0366).

If the viscosity increases due to evaporation, this must be compensated for using water (target viscosity: clear, special colours, lignin-stabilising: runout time approx. 23 - 27 s in ISO cup 3 mm; white: runout time approx. 34 - 45 s in ISO cup 3 mm)

Dilute with up to 10% water to improve flow properties in unfavourable conditions (elevated temperatures, low humidity). Add water to make up for any moisture lost through evaporation.

If foaming occurs in the flow coating system, it is recommended to add 0.2-1.0% VP 9325 defoaming agent - strength 2.

Contact our technical support team on 0113 2455450 (option 2) or send a message to [email protected] for coating recommendations for specific wood types to be used when treating windows and exterior doors.

Observe the “Care and Maintenance of Dipping Tanks and Flow Coating Facilities” and “Notes on Operational Hygiene” information sheets, available to download from the "Attachments" section above.

Drying

Can be overcoated: after approx. 4 hours (at 23 °C and 50% RH)

If forced drying is used, can be overcoated: after approx. 90 minutes (20 minutes dripping/50 minutes drying phase (35 – 40 °C)/20 minutes cooling phase)

Low temperatures, poor ventilation and high humidity delay drying.

Thinning

Ready for use

Tools / Cleaning

Brush, dipping tank, flow coating facility, spray coating facility, vacuum machine.

Clean tools with water or Aqua RK-898 Cleaning Concentrate immediately after use.

Ensure that any residue from cleaning is disposed of correctly.

Storage / Shelf Life

Store in well-sealed, original containers, out of the reach of children and in a dry, cool, well-ventilated room which is protected from direct sunlight and frost. No smoking is permitted in storage areas.