Remmers Aqua VL-66/sm-Venti Coat 3in1

7090
REM4906

Remmers Aqua VL-66/sm-Venti Coat 3in1 is a water-based one-pot coating system with a sealing effect for high-value wooden structures.

  • For use on interior and exterior wood
  • Dimensionally stable wood building elements: e.g. windows and doors
  • Wood building elements with limited dimensional stability, e.g. folding shutters, matchboarding, summerhouses
  • Wood building elements with no dimensional stability: e. g. fences, framework, carports, planking
  • Not suitable for coating floors (terraces, wooden decking, etc.)
  • For use by professionals
  • 2000+ colours available, in RAL, NCS and British Standard

Product customisation

Don't forget to save your customization to be able to add to cart
  • 250 char. max
Colour Group
Size
Finish
£20.11(ex. VAT)
£24.13 (inc. VAT)
Quantity
Please choose your colour
Available for Delivery (See Delivery Options Below)

Description

Remmers Aqua VL-66/sm-Venti Coat 3in1 is a water-based one-pot coating system with a sealing effect for high-value wooden structures, with a wide range of uses that include:

  • For use on interior and exterior wood
  • Dimensionally stable wood building elements: e.g. windows and doors
  • Wood building elements with limited dimensional stability, e.g. folding shutters, matchboarding, summerhouses
  • Wood building elements with no dimensional stability: e. g. fences, framework, carports, planking
  • Not suitable for coating floors (terraces, wooden decking, etc.)
  • For use by professionals
  • 2000+ colours available, in RAL, NCS and British Standard



Quick Links - Click To Jump To Section:




Features & Benefits


  • Water-based
  • Base coat, intermediate coat and topcoat all in one
  • Ventilating effect
  • Block resistant (in accordance with Code of Practice HO.03)
  • Resistant to extreme temperatures and little tendency to yellow
  • Isolating effect against substances contained in the wood
  • Inhibits rust from screws and nail heads
  • Highly weather-resistant and low-chalking



Application Rate


100-120 ml/m² per coat

2 coats are required to seal off substances contained in the wood.



Product Data


  • Density (20 °C): approx. 1.27 g/cm³
  • Viscosity: approx. 1800 mPa∙s
  • Odour: mild

The values stated represent typical characteristic data of the product and are not to be understood as binding product specifications.



Certificates


  • DIN EN 71-3 (Children's toy safety)



Possible System Products


  • Aqua IG-15 Impregnation Primer IT* (7145)
  • Aqua AG-26 All Primer (7147)
  • Induline SW-910 (3777)

*Use biocidal products carefully.

Always read the label and product information before use.



Preparation


Substrate requirements

Dimensionally stable wood building elements: wood moisture content 11-15%

Wood building elements with limited or no dimensional stability: wood moisture content max. 18%

 

Substrate preparation

Thoroughly remove any dirt, grease and non-adhering old coatings.

Thoroughly sand any old coatings that are still intact.

Sand grey and weathered wood surfaces down to sound, bright wood.

Aqua IG-15 Impregnation Primer IT* should be used to pre-treat wood in outdoor areas which requires protection against insects, rot and blue stain (omit step for wood in indoor areas).

Observe BFS Code of Practice No. 18 "Coatings on Wood and Wooden Working Materials in Outdoor Areas".



Directions


Conditions for use

Temperature of the material, air and substrate: from min. +5 °C to max. +25 °C

Stir well.

Apply with a brush, roller or by spraying.

  • Flow cup gun: nozzle size: 2.0 - 2.5 mm; atomiser air pressure: 2.0 - 3.0 bar.
  • Airless spraying: nozzle size: 0.23 - 0.28 mm, material pressure: 80 - 120 bar.
  • Airmix spraying: nozzle size: 0.23 - 0.28 mm, material pressure: 80 - 100 bar, atomiser air pressure: 1.2 - 2 bar.

Re-coat once dry.

Seal opened containers well and use contents as soon as possible.



Tips on Use


Areas that are being coated or dried should be protected against rain, wind, sunlight and condensation.

Check the product’s compatibility with the substrate and its insulating effect by applying a trial coat.

The colour shown on the sample does not appear until the material has dried.

 

Drying

Dust dry: after 1–2 hours

Can be overcoated: after approx. 6 hours

Practice values at +20 °C and 65% relative humidity.

The coating may take significantly longer to dry thoroughly in lower temperatures, at high humidity or if the maximum layer thickness has been exceeded.

Longer drying times can improve the insulating effect.

 

Thinning

Ready to use



Notes


Insulation of resins and substances contained in the wood.

The instructions regarding coats, application volumes and drying times for the coating system must be followed to ensure the best possible insulation for water-soluble substances contained in the wood (flat surfaces and branches). The first coat can activate substances in the wood and discolour the film on the coating, which will lock the substances inside the film. The second coat of insulating product will then seal off the substances contained in the wood.

At least two coats of the product are required to achieve an efficient insulating effect.

If discolouration continues even after following these steps, we recommend contacting our RTS (Remmers Technical Service).

Bleeding resin is a natural phenomenon and cannot be prevented by coating measures, see BFS Code of Practice No. 18.

The product’s insulating effect may be impaired if it is diluted too thinly, if the wood is too wet or if the recommended coating sequence, application volumes and drying times are not observed. With water-based coating systems, there is always the residual risk that substances contained in the wood will leach out.

On planed larch and softwoods with a high resin content, the coating may have reduced adhesion and resistance to weathering. This is especially the case on horizontal year rings, knots and areas of winter growth that are high in resin. Maintenance and renovation must be carried out more frequently on these surfaces. The only remedy for this is pre- weathering or very coarse sanding (P80). If these wood types are rough-sawn, considerably longer maintenance and renovation intervals are to be expected.



Tools / Cleaning


Acrylic brush/synthetic fibre brush, microfibre paint roller, flow cup or airless spraying equipment

Clean tools immediately after use with water and detergent.

Ensure that any residue from cleaning is disposed of correctly.



Storage / Shelf Life


If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 12 months.



Personal Protective Equipment


Respiratory protection with a particle filter P2 must be worn during spraying, together with protective goggles. Wear suitable protective gloves and clothing.

Product Details
7090

Data sheet

Manufacturer
Remmers
Interior / Exterior Use
Interior and Exterior
Water / Solvent Based
Water
For Use On
Wood, Prepared
Application Method
Brush, Roller, Spray
Sheen
Silk Matt
Colour
Standard / Ready Mixed
VOC Levels
Low (50-149 g/l)
Single, Two or Three Pack
Single
Product Certifications
DIN EN 71-3 (Children's toy safety)
Pack Size
750ml, 2.5L, 5L, 20L
Coverage
100-120 ml/m² per coat
Density
approx. 1.27 g/cm³
Viscosity
approx. 1800 mPa∙s
Exterior / Interior Use
Exterior Use
Type of Wood Finish
Wood Paint
Suitable For
Walls & Ceilings
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send