A range of water-based grey stains that penetrate deep into the wood for a lasting grey ‘weathered wood’ look. Only need to apply once, then a topcoat can be applied.
Mathys Fassilux Aqua XPE Satin
A water based, satin finish for interior and exterior timber and previously painted mineral substrates to provide a smooth, scratch resistant finish.
Mathys Fassilux Aqua XPE Satin is a water dilutable air-drying satin topcoat for interior and exterior works. Produces a scratch resistant satin finish on properly prepared wooden, or other already painted mineral substrates.
Features & Benefits
- Can be used in- and exterior
- Quick drying
- Low in odour and VOC,
- Easy to apply
- Excellent flow and levelling characteristics
- Superior scratch resistance
- Stable gloss
- Good adherence, hiding power and elasticity
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
- Brush, Roller, Spray
- 12m² per litre
- Touch Dry
- 3 hours
|Dorota on 28/07/2016|| |
Question: Hi there, I am using Mathys Fassilux Aqua XPE Satin - Colour: RAL1023 for painting wooden cupboard doors. The doors have been previously painted, so I sanded them down to roughen the surface for the paint to stick better, then applied Zinsser BIN shellac primer and then the Fassilux, as a thin layer (just one coat in places, two in others). A week on, and the paint still feels somewhat tacky. The same occurred on Zinsser BIN primed ply board - a week on, and still a bit tacky. Tacky to the extent that if you put one Fassilux painted surface touching another Fassilux painted surface, they stick to each other a bit. Is there anything I can do to speed up the drying process? Talcum powder? Some shelves I painted with Mathys Pegacryl Satin - Colour: RAL6027, same conditions, same time, happily accepted 2 coats, dried completely in 24 hours and are now done, whereas the Fassilux is still playing up... Thanks very much for your help!
Please refer to the Technical Data Sheet (TDS) for each product which can be downloaded from the 'DATASHEETS' tab on each respective product page on our website. Here it states that Mathys Fassilux Aqua XPE Satin should be touch dry in 3 hours, recoatable after 24 hours and full hardness will be achieved after 1 week. Mathys Pegacryl Satin is quicker drying at touch dry in 1 hour, recoatable in 24 hours and full hardness will be achieved after 2 days. All estimated drying times are based on 20°C and 50% r.h., low temperatures, lack of air flow and high relative humidity will prolong the drying/curing process.
Blackfriar French Polish provides the classic fine finish for wood. It’s suitable for new, stained, or previously French Polished wood and brings out the natural beauty of wooden surfaces.
Transform your interior wooden surfaces with Blackfriar Quick Drying Varnish. Ideal for all interior wood including doors and panelling, it provides a quick drying finish that is tough and durable. Blackfriar Quick Drying Varnish resists knocks, hot water splashes and some household stains.
Perfect for when you need a dead black matt surface. Its non-reflective finish makes it ideal for all interior surfaces such as old beams, panelling, decorative ironwork, stage scenery and darkrooms. To be used on wood and metal.
Thermilate InsOpaint Gloss is an innovative, eco-friendly, water based gloss paint with a non-yellowing finish, ideal for interior wood and metal. This specially formulated, water based gloss gives all the appearance and characteristics of traditional gloss but has advanced durability, high opacity and fast drying times.
Coo-Var Matt Black Water Based is a high opacity flat black acrylic coating providing a finish to internal surfaces anywhere a non-reflective surface is required. ADVANTAGES Water-based Less odours than solvent-based Fast drying Non-reflective Decorative Apply directly to wood and masonry Can be used on cement
Blackfriar Wood Dye penetrates deep into wood to enrich the colour of bare timber. It can be used on new interior and exterior timber, plywood and chipboard. Plus you can also mix the dye colours to create your own individual shades.
Timberex Wax-Oil greatly enhances colours and grain and allows wood to age naturally into rich varying tones. Made from fast curing natural oils and carnuba wax it cures to a deep satin finish.
Coo-Var Danish Oil is a hard, durable, water resistant seal for the enhancement of interior and exterior wood containing tung oil. ADVANTAGES Harder finish than teak oil Durable Water resistant Slight gloss finish
Offers a compromise of a tradtional oil and a coating with superior protection against spillages. It greatly enhances colours and grain and allows wood to age naturally into rich varying tones.
A low-VOC wood oil for protection against stains and wear. Very rapid curing saves time and costs. Non-yellowing, non-darkening and easy to maintain and clean. Can be used as a Topcoat for Timberex Aqua and Active Stain.
Blackfriar Danish Oil provides a beautiful, low lustre satin, scratch-proof finish. You can use it inside and outside for most wooden surfaces including furniture, doors, panelling, wood decorations and woodturning.
Get creative – enrich and gild interior and exterior surfaces with Blackfriar Metallic Paint. Ideal for ornamental plasterwork, picture frames, decorations, theatre props, furniture, radiators and textured wall finishes.
Coo-Var Matt Black is an oil-based, flat black finish for interior and exterior use anywhere a non-reflective surface is required. ADVANTAGES Decorative Interior/Exterior use Non-reflective Apply direct onto wood and masonry Can be used on chalk