Blackfriar Professional Paint & Varnish Remover removes old coatings quickly and effectively. It works on a variety of finishes including gloss and emulsion paints, varnish and French polish. Effective on wood, metal and glass, the fast acting formula has a non-drip consistency, which makes it easy to apply to all surfaces. It will not...
Blackfriar Quick Drying Floor Varnish
Blackfriar Quick Drying Floor Varnish has been specially formulated to protect floors with an attractive, long-lasting scratch-resistant finish. The varnish dries quickly so you could transform your floors in just one day. Easy to clean and perfect for all wooden flooring.
- For all interior wooden doors.
- Scratch and slip-resistant finish.
- Quick drying - touch dry in just 60 minutes.
- Non yellowing.
- Easy to clean.
Blackfriar Quick Drying Floor Varnish has been specially formulated to protect the floors in your home with an attractive, long-lasting scratchresistant finish. The satin finish provides additional slipresistance. The varnish dries quickly so you could transform your floors in just one day. Easy to clean and perfect for all wooden flooring.
Ensure surface to be varnished is clean, dry, sound and free from wax, oil or any other contamination. If wax has been used clean the surface thoroughly with white spirit prior to sanding. Bare wood should be sanded to a smooth surface, always working with the grain. Sound, previously varnished surfaces should be lightly sanded to provide a key. Existing varnished surfaces which are unsound or in poor condition can be stripped back to bare timber with Blackfriar Professional Paint and Varnish Remover.
Stir thoroughly prior to use. The product may be applied by brush or roller. If applying by brush, apply evenly using light strokes following the grain of the wood. If rollering, use a short nap mohair roller. For best results 3 coats are recommended on new wood and 2 coats on previously varnished surfaces. Prior to application of the final coat or if the overcoating time is exceeded lightly abrade with fine glass paper working with the grain and remove dust. The varnish will appear cloudy when wet but will quickly dry to a clear finish. When applying to new or bare wood, thin the first coat with up to 10% water
Not suitable for use on plastic type materials, eg. imitation wood. If applying varnish to cork tiles, prefinished tiles or laminate flooring we recommend a trial application on an inconspicuous area of the floor. Once dried check adhesion by scratching firmly with a finger nail. New concrete should be allowed to dry for at least 6 months before varnishing. Do not use under cold (less than 10°C), damp or humid conditions. Do not wash the varnished surface for at least 3 days after application. If water is spilled on it during this period gently wipe off with a soft dry cloth.
Touch dry in 1 hour. Recoat after 4 hours and within 3 days. Drying times are based on ambient temperature of 20°C and 50% humidity. Lower temperatures and higher humidity levels will prolong drying and overcoating times.
Remove as much paint as possible from equipment before cleaning. Clean with warm water, rinse and dry thoroughly.
Store in a dry, safe place. Do not store in environments where extreme temperatures may occur. Keep within 5-30°C. Do not store in direct sunlight.
- For wooden floors
- Scratch and slip-resistant finish
- Quick drying
- Easy to clean
Please contact Rawlins Paints' Technical Support Team on 0113 2455450 for more information
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
- Blackfriar Professional
- Base Type
- Water Based
- Interior/Exterior Use
- Brush, Roller
- Dry to Recoat (at 20°C)
- 4 hours
- 14m² per litre
- Recommended Thinner/Cleaner
- Touch Dry
- 1 Hour
- UN Number
|Simon on 09/03/2019|| |
I am looking for a tough wood floor finish where the floor has been sealed with an oil based polyurethane varnish previously. It has to stand up to scratching and scuffing by dogs and wheelchair. Will this be tougher than the other polyurethane products?
Blackfriar Quick Drying Floor Varnish would have similar durability to the Polyurethane floor varnish. If the floor boards are pine softwood it would be best to stick with the current polyurethane varnish. Abrade the surface first with a fine grade of sandpaper, wash down well to remove all contamination then apply 2 coats. If the floor boards are oak or a similar hardwood, the toughest varnish we do is the Blackfriar Heavy Duty Varnish. This is not suitable for softwoods, the cured varnish is too brittle and is likely to craze over time due to expansion and contraction of the softwood.
A low-VOC wood oil for protection against stains and wear. Very rapid curing saves time and costs. Non-yellowing, non-darkening and easy to maintain and clean. Can be used as a Topcoat for Timberex Aqua and Active Stain.
Timberex Wax-Oil greatly enhances colours and grain and allows wood to age naturally into rich varying tones. Made from fast curing natural oils and carnuba wax it cures to a deep satin finish.
For commercial or domestic use, on floors, stairs, panelling etc. Timberex Coloured penetrates deeply into the wood filling the pores to form a wear and water resistant surface.
Coo-Var P101 2 Pack Polyurethane Varnish is a clear aliphatic polyurethane coating which provides a hard wearing protective coating for wooden floors, both inside or outside. Product Details For interior and exterior use Suitable surfaces: Wood Finish: Gloss Application: Roller, brush or airless spray
Blackfriar Heavy Duty Varnish is a two pack varnish that protects and transforms floors and work surfaces with a tough, hardwearing and professional finish. Resists dilute acids and alkalis, grease and chemicals, making it ideal for use in high traffic areas. Available in gloss and satin finishes. Product Features Durable polyurethane...
Resupen WB is a an extremely durable polyurethane finish for concrete, plaster and wood that produces a resilient coating on Sherwin-Williams wall and flooring systems. It is available in clear, colour, matt and satin finish. ADVANTAGES Chemical resistant UV stable Good abrasion and impact resistance Hygienic and easy to clean No VOC’s...
Used for periodic maintenance of floors treated with Timberex Gold, Timberex Free or Timberex Wax-Oil. A deep penetrating, hardening natural oil that is labour efficient and re-sanding is not normally necessary.
Rust-Oleum 4900 Polycoat 2K is a clear, water-based, 2-component polyurethane topcoat for use on wood, concrete and pre-painted surfaces, also serves as an anti-graffiti coating. Very abrasion resistant, available in a matt or gloss finish, does not yellow, can be used internally and externally, resists boiling water, alcohol, coffee, red...
A range of water-based stains for interior use that penetrate deep into the wood for a lasting colour effect without losing the ‘wood’ look. The stains are fastdrying, allowing the topcoat to be applied within a few hours, minimizing time and costs.
Coo-Var Polyurethane Clear Floor Coating is a single pack product of exceptional durability based on urethane alkyd. Product Features Perfect for kitchen furniture Worktops Internal doors For interior use only
Blackfriar Polyurethane Floor Varnish provides the perfect finish for most wooden floors. Provides an attractive, durable and protective finish which is easy to clean and seals the surface against dirt. Product Features Interior use. For all types of wood. Tough and durable. Resistant to hot water splashes, dilute acids/alkalis and some...
Offers a compromise of a tradtional oil and a coating with superior protection against spillages. It greatly enhances colours and grain and allows wood to age naturally into rich varying tones.
Jotun Trestjerner Parkettlakk is a quick-drying, high quality, water-borne polyurethane clear varnish with low odours for use on wooden laminate/parquet floors. It has a high resistance to wear and scratches and a good chemical resistance. The product adheres well to the flooring enhancing the appearance, and it contains a UV-filter against...
Rust-Oleum Chalky Finish Floor Paint renovates and transforms wood, concrete and previously painted surfaces with a a hard wearing flat matt finish that is suitable for wooden floorboards or concrete flooring, resisting knocks and scratches. Water based with virtually no odour Highly concentrated, with exceptional coverage - Up to 14m2 /...