• Blackfriar Heavy Duty Varnish

Blackfriar Heavy Duty Varnish

BF214

Blackfriar Heavy Duty Varnish is a two pack varnish that protects and transforms floors and work surfaces with a tough, hardwearing and professional finish. Resists dilute acids and alkalis, grease and chemicals, making it ideal for use in high traffic areas. Available in gloss and satin finishes.

Product Features

  • Durable polyurethane finish.
  • Low odour.
  • Non-yellowing.
  • Clear, water-based formula.
  • Indoor use.
  • Suitable for wooden floors, furniture and concrete surfaces.
  • Brush or roller application.
Colour
Size
Finish
£61.00
VAT excluded

£73.20 Tax incl.
Quantity

Description

Blackfriar Heavy Duty Varnish is a two-pack varnish that protects and transforms floors and work surfaces with a tough, hard wearing and professional finish. Resists dilute acids and alkalis, grease and chemicals, making it ideal for use in sports halls, gymnasiums and on bar tops.

Preparation

Ensure surface to be varnished is clean, dry, sound and free from wax, polish, oil or any other contamination. If wax has been used clean the surface thoroughly with white spirit prior to sanding. Bare wood should be sanded to a smooth surface, always working with the grain. Sound, previously varnished surfaces should be lightly sanded to provide a key.

Existing varnished surfaces which are unsound or in poor condition can be stripped back to bare timber with Blackfriar Professional Paint and Varnish Remover. New concrete must be at least 6 months old prior to varnishing. Concrete must be clean, dry and free from any surface laitance (a weak dusty layer on new concrete) and any other surface contaminants such as oils, grease, dirt etc. prior to applying the varnish. Power floated concrete must be prepared by suitable means (mechanical or chemical) to ensure an open, porous, sandpaper texture is achieved prior to varnishing.

Mixing

Base and activator supplied in correct proportions. Add all activator to base container and mix thoroughly for at least 5 minutes until product is smooth and even. Allow to rest 5 minutes before using. DO NOT MIX PART UNITS. Badly activated or incorrectly mixed materials will affect performance and may cause early failure or discolouration. The mixed material has a usable pot life of 4 hours (20°C).

Application

The product may be applied by brush or roller. If applying by brush, apply evenly using light strokes following the grain of the wood. If rollering, use a short nap mohair roller. For best results 3 coats are recommended on new wood and 2 coats on previously varnished surfaces. Prior to application of the final coat or if the over coating time is exceeded, lightly abrade with fine glass paper working with the grain and remove dust. The varnish will appear cloudy when wet but will quickly dry to a clear finish. When applying to new or bare wood, thin the first coat with up to 10% water.

Limitations

Not suitable for use on floor tiles or plastic type materials, e.g. imitation wood. Do not apply directly to power floated concrete. New concrete should be allowed to dry for at least 6 months before varnishing. Do not use under cold (less than 10°C), damp or humid conditions. Do not wash the varnished surface for at least 3 days after application. If water is spilled on it during this period gently wipe off with a soft dry cloth.

Drying Time

Touch dry - 2 hours (20°C). Hard dry - 8 hours (20°C). Full cure - 3 days (20°C). Recoatable after 4 hours.

Clean Up

Remove as much product as possible from application equipment before washing with water. Do not empty into drains or water courses. Some local authorities have special facilities for the disposal of waste coatings.

Features

  • Clear, durable, water-based polyurethane finish.
  • Low odour, non-yellowing.
  • Chemical and stain resistant
  • Suitable for indoor use on wooden floors, furniture and concrete surfaces.

It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.

Product Details
BF214

Data sheet

Manufacturer
Blackfriar Professional
Parts
Two
Base Type
Solvent Based
Interior/Exterior Use
Interior
Application
Brush, Roller
Coverage
12m² per litre
Recommended Thinner/Cleaner
Water
Touch Dry
2 Hours
UN Number (Activator)
N/A
UN Number (Base)
N/A
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


questions Emily Harris  on 02/01/2017
Question: Can you use this product on a painted surface to provide a hardwearing suface I.e a bar area were glasses etc are in and out to prevent scuffs and scratches on the unit hope to hear back from yourselves thanks Emily
Answer: 

Blackfriar Heavy Duty varnish should is fine to go over most previously painted surfaces. With it being a 2 pack it will be harder wearing than single pack paint products. We would advise giving the surface a good rub down with a fine grade of sandpaper to key up the surface then wiping with Methylated Spirits to remove all dust.

Apply 2 coats of the varnish following the application instructions carefully. Allow the varnish to cure fully for 7 days before subjecting the coating to any abrasion from glasses etc.


Question about the product

* Required fields
(read)
Send
You might also like

Blackfriar Professional Paint & Varnish Remover

Blackfriar Professional Paint & Varnish Remover removes old coatings quickly and effectively. It works on a variety of finishes including gloss and emulsion paints, varnish and French polish. Effective on wood, metal and glass, the fast acting formula has a non-drip consistency, which makes it easy to apply to all surfaces. It will not...

Price £19.68
In stock
16 other products in the same category:

Jotun Trestjerner Parkettlakk

Jotun Trestjerner Parkettlakk is a quick-drying, high quality, water-borne polyurethane clear varnish with low odours for use on wooden laminate/parquet floors. It has a high resistance to wear and scratches and a good chemical resistance. The product adheres well to the flooring enhancing the appearance, and it contains a UV-filter against...

Price £67.37
In stock

Timberex Gold

A virtually solvent-free product made from natural, fast-drying oils and resins which penetrate deeply into the wood. Filling and enriching the pores it cures to seal and protect from within

Price £24.16
In stock

Timberex Aqua Plus

Timberex Aqua Plus is a water-based polymer wood coating for fast and easy industrial protection. Very rapid curing saves time and costs. Stains and protects at the same time.

Price £26.15
In stock

Timberex Hard-Wax Oil

Offers a compromise of a tradtional oil and a coating with superior protection against spillages. It greatly enhances colours and grain and allows wood to age naturally into rich varying tones.

Price £19.32
In stock

RSL Resupen WB

Resupen WB is a an extremely durable polyurethane finish for concrete, plaster and wood that produces a resilient coating on Sherwin-Williams wall and flooring systems. It is available in clear, colour, matt and satin finish. ADVANTAGES Chemical resistant UV stable Good abrasion and impact resistance Hygienic and easy to clean No VOC’s...

Price £105.44
In stock

Timberex Satin Oil

Used for periodic maintenance of floors treated with Timberex Natural, Timberex Heavy Duty or Timberex Coloured. Available in natural or white, re-sanding is not normally necessary.

Price £15.29
In stock

Mathys Plasti-Parket

Mathys Plasti-Parket is a solvent based polyurethane alkyd varnish ideal for treating and protecting parquet floors and wooden stairs.  Simple to use Air-drying Excellent resistance against abrasion Makes maintenance easier Suitable for spot repairs 

Price £32.36
In stock

Coo-Var P101 2 Pack Polyurethane Varnish

Coo-Var P101 2 Pack Polyurethane Varnish is a clear aliphatic polyurethane coating which provides a hard wearing protective coating for wooden floors, both inside or outside. Product Details For interior and exterior use Suitable surfaces: Wood Finish: Gloss Application: Roller, brush or airless spray

Price £127.87
In stock

Coo-Var Clear Glaze for Wooden Floors

Coo-Var Clear Glaze for Wooden Floors can be used on wooden and concrete floors to provide a quick drying and protective clear coat. A water based product for both domestic and commercial use. Product Features Quick drying Protective, clear coat Domestic/Commercial use Low odour Ideal for use where fast drying and no solvent smell is...

Price £13.58
In stock

Timberex Satin Oil Gold

Used for periodic maintenance of floors treated with Timberex Gold, Timberex Free or Timberex Wax-Oil. A deep penetrating, hardening natural oil that is labour efficient and re-sanding is not normally necessary.

Price £20.23
In stock

Timberex Heavy-Duty UV PLUS

An improved version of the Timberex Heavy-Duty UV wood oil, with improved coverage, smell, water resistance, UV resistance and faster curing. 

Price £19.44
In stock

Timberex Heavy Duty UV

Now includes a UV-blocker which will inhibit the bleaching of the surface by harmful UV rays using natural, fast drying oils and resins which penetrate deeply into the wood.

Price £18.80
In stock

Timberex Coloured

For commercial or domestic use, on floors, stairs, panelling etc. Timberex Coloured penetrates deeply into the wood filling the pores to form a wear and water resistant surface.

Price £18.47
In stock

Timberex Aqua

A range of water-based stains for interior use that penetrate deep into the wood for a lasting colour effect without losing the ‘wood’ look. The stains are fastdrying, allowing the topcoat to be applied within a few hours, minimizing time and costs.

Price £18.81
In stock

Rust-Oleum 4900 Polycoat 2K

Rust-Oleum 4900 Polycoat 2K is a clear, water-based, 2-component polyurethane topcoat for use on wood, concrete and pre-painted surfaces, also serves as an anti-graffiti coating. Very abrasion resistant, available in a matt or gloss finish, does not yellow, can be used internally and externally, resists boiling water, alcohol, coffee, red...

Price £25.52
In stock