Sikabond MS Wood Floor Gun Grade
  • Sikabond MS Wood Floor Gun Grade

SikaBond MS Wood Floor Gun Grade

FPSKBDMSFL6

SikaBond MS Wood Floor Gun Grade is a high quality, gun-applied MS adhesive for bonding wooden floors to all common substrates. Being permanently elastic it accommodates differential movement caused by changes in humidity and climatic conditions.

  • 100% active, solvent and water free – will not cause warpage or curl of wood blocks/planks
  • Permanently flexible – compensates for subfloor movement
  • Suitable for use with underfloor heating (due to high flexibility)
  • Odourless
  • Excellent gap filling properties for uneven surfaces
  • Excellent sound deadening/acoustic properties
  • Click to jump down to Technical Data
Colour
Size
£106.92
VAT excluded

£128.30 Tax incl.
Quantity

Description

SikaBond MS Wood Floor Gun Grade is a high quality, gun-applied MS adhesive for bonding wooden floors to all common substrates. Being permanently elastic it accommodates differential movement caused by changes in humidity and climatic conditions. When used as part of the Sika AcouBond system, it is ideal for use with underfloor heating systems. Bonds directly to all common subfloor materials – concrete, anhydrite, chipboard, plywood, metal, ceramic tiles, and most natural stone floors.

Note: for other substrates call Sika Technical Services, Rawlins Paints' Technical Support Team on 0113 2455450 (option 2) or send a message to [email protected] for more information.



Quick Links - Click To Jump To Section:




Features & Benefits


  • Bonds directly to all common subfloor materials
  • 100% active, solvent and water free – will not cause warpage or curl of wood blocks/planks
  • Permanently flexible – compensates for subfloor movement
  • Suitable for use with underfloor heating (due to high flexibility)
  • Odourless
  • Excellent gap filling properties for uneven surfaces
  • Full bed elastic product gives excellent sound deadening/acoustic properties
  • Coverage of 2m2 per 600ml foil pack



Preparation


All surfaces must be sound, clean, dry and free from dust, grease or other contaminants that can affect adhesion. Existing floors must be free from all polish/wax/silicone/sealers etc.

For cement based substrates with a moisture content >2% CM (Carbide Method) but < 4% CM, apply Sika Primer MB or SikaBond Rapid DPM as a liquid damp proofing membrane. N.B Never apply damp proof membranes on top of a wet anhydrite screed. Always check moisture content of subfloor and record readings. If in doubt please consult a specialist. Where moisture levels are above those recommended by the flooring manufacturer but below 4% CM (6% Tramex), prime with Sika Primer MB or SikaBond Rapid DPM.

Basement/below ground floors: ensure climatic conditions are appropriate for the installation of wood flooring. Flooring substrate must be adequately protected from moisture ingress under hydrostatic pressure. Where a vapour barrier is required apply two coats of SikaBond Primer MB or SikaBond Rapid DPM.

All underfloor heating systems should be fully commissioned prior to installation of any floor finishes. Turn off any underfloor heating systems 24 hours before, and until 24 hours after, applying the adhesive. Flooring should be acclimatised for several days in the room where it is to be installed.



Application


Remove metal sealing clip from the foil pack and place into a suitable barrel gun. Screw on pre-cut ‘V’ shaped nozzle, hold the gun at 90 degrees to the floor, and extrude out a triangular shaped bead approx. 8mm wide and 10mm high at maximum 250mm centres, at right angles to the length of the wood plank. Place wood in position whilst adhesive is still wet (within 30mins). Press firmly and tap into position with a mallet. Ensure you leave a 12-15 mm expansion gap along walls and around surface protrusions for the wood to expand. Always check with flooring manufacturer for specific instructions relating to their flooring. Always carry out installations and sub-floor preparation in line with relevant British or International standards.



Limitations


  • Do not use directly on bitumen or asphalt floors, or substrates that bleed oil or plasticisers.
  • Do not use, store or allow to cure below +5°C.
  • Do not use externally.



Coverage


2m2 per 600ml foil pack.



Drying Time


Touch dry in 30 mins, full cure in 36-48 hours.



Clean Up


Fresh, uncured adhesive remaining on the wood surface must be removed immediately and if necessary cleaned with Sika Remover-208. Test wood floor surfaces for compatibility with Sika Remover-208 before use. Cured adhesive may be removed from prefinished flooring using a suitable plastic scraper and/or pencil eraser.



Value Base


All technical data stated in the Products Data Sheets are based on laboratory tests. Actual measured data may vary due to circumstances beyond our control.



Health And Safety


For information and advice on the safe handling, storage and disposal of chemical products, users shall refer to the most recent Safety Data Sheet (SDS) containing physical, ecological, toxicological and other safety-related data.

 

Please contact Rawlins Paints' Technical Support Team on 0113 2455450 (option 2) or send a message to [email protected] for more information.

Click to go back to the top of the page

It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.

Product Details
FPSKBDMSFL6

Data sheet

Manufacturer
Sika
Parts
One
Interior/Exterior Use
Interior
Suitable Substrates
Concrete, Anhydrite, Chipboard, Plywood, Metal, Ceramic Tiles, Stone Floors
Application
Barrel Gun Applicator
Fully Cured (at 20°C)
36-48hrs
Coverage
2m² per 600ml foil pack
Min. Application Temperature
5°C
Density
1.5 - 1.6 g/cm³ at 20°C
Shelf Life (from date of manufacture)
12 Months
Touch Dry
30mins
UN Number
N/A
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send
You might also like

Sika Remover 208

Sika Remover 208 can be used for removing traces of Sikaflex products from unwanted places and tools and it is also ideal to clean painted surfaces prior to bonding. Uses: Removes uncured excess material of Sikaflex adhesive or sealant from application tools or from soiled surfaces Pre-cleaning of strongly contaminated non-porous...

Price £12.99
In stock

Sika Primer MB

Sika Primer MB is a primer and moisture control coating for cementitious substrates prior to levelling or bonding with elastic sikabond adhesives. It is a one coat, 2-part, solvent free, low viscosity, epoxy resin primer for use in conjunction with Sika Schönox levelling compounds, dispersion primers and SikaBond Wood Floor adhesives....

Price £89.99
In stock

SikaBond Rapid DPM

SikaBond Rapid DPM is a solvent free reaction curing resin primer and damp proof membrane for cement based substrates. Used for priming, consolidating and sealing of absorbent and non-absorbent sub-floors, consolidating weak cement screed and isolation of old adhesive residues.  Features &amp; Benefits 1-part, ready to use. Rapid drying...

Price £225.99
In stock