HMG AIF630 Button Polish

    LACAIF630
    HMG4445

    HMG AIF630 Button Polish is a pale coloured sealer for use on wood and metal surfaces.  Its fast drying characteristics and ease of application lends itself to a whole variety of usages.

    • The product is a modified resin type and is non-toxic and thus suitable for food contact.
    • Suitable for use using a rubber for French Polishing purposes.

    Colour
    Size
    Finish
    £123.14(ex. VAT)
    £147.77 (inc. VAT)
    Quantity
    Please choose your colour
    Available for Delivery (See Delivery Options Below)

    Description

    HMG AIF630 Button Polish is a pale coloured sealer for use on wood and metal surfaces.  Its fast drying characteristics and ease of application lends itself to a whole variety of usages.



    Click To Jump To Section:




    Features & Benefits


    • The product is a modified resin type and is non-toxic and thus suitable for food contact.
    • Suitable for use using a rubber for French Polishing purposes.



    Product Specification


    Technical Data
    HMG AIF630 Button Polish
    Volume Solids:30.9%
    VOC Content:0.6kgs/ltr
    SG:-
    Viscosity:100 mPas
    Density:0.882 g/cm³
    Storage Conditions:Store between 5°C - 25°C. When not in use, cans must be kept sealed.
    Shelf Life:12 months from delivery date in original sealed containers.
    Pot Life:n/a
    Flash Point:13°C



    Film Thickness Range And Coverage


    Product Data
     Dry Film ThicknessWet Film Thickness
    Brush:n/an/a



    Coverage: 15 square metres per litre at 25 microns dft (Theoretical)

    • HMG technical data sheets indicate a dry film thickness that will be achieved when applying a particular wet film thickness.
    • These values are a guide only and are not to be used as specifications.
    • Film thickness will vary depending on actual use and specification.
    • Great care should be taken to achieve the dft stated in the agreed specification and to avoid areas of excessively low or high thickness.



    Drying Times


    Drying Times At 20°C
    Dry To Recoat:After hard dry
    Fully Cured:20 - 30 minutes



    Surface Preparation


    • Ensure surfaces to be coated are dry and must be cleaned using the appropriate HMG product to remove all traces of contaminants.
    • Read and follow the safety data sheet, product data sheet and label instructions.
    • Stir all paints thoroughly before use.
    • Always use the same batch number on the same job.
    • Check colour & sheen.
    • Filter the product immediately before use.
    • Reduce emissions and maintain quality by replacing tin lid after use.



    Application Methods


    Technical Data
    Brush
    Mixing Ratio:Ready for use
    -
    Thinner Options:Thinner 2671
    Viscosity:n/a
    Spray Gun Setup:n/a
    Number Of Coats (Guide Only):2 - 3 coats
    Flash Off:n/a



    For further information on mixing ratios please contact Rawlins Paints on Tech - 0113 2455450 (option 2) or [email protected] Sales - 0113 2455450 or [email protected]



    Product Notes


    Information On Basic Physical And Chemical Properties
    HMG AIF630 Button Polish
    Form:According to product specification
    Colour:According to product specification
    Odour:Characteristic
    Odour Threshold:Not determined
    pH-value 20°C:Not determined
    Melting point/freezing point:Undetermined
    Initial boiling point and boiling range:78°C
    Flash Point:13°C
    Flammability (solid, gas):Not applicable
    Ignition temperature:300°C
    Decomposition temperature:Not determined.
    Auto-ignition temperature:Product is not selfigniting.
    Explosive properties:"Product is not explosive. However, formation of explosive air vapour mixtures are possible."
    Explosion limits: Lower:3.5 Vol %
    Explosion limits: Upper:15.0 Vol %
    Vapour pressure at 20°C:59 hPa
    Density at 20°C:0.882 g/cm³
    Relative density:Not determined
    Vapour density:Not determined
    Evaporation rate:Not determined
    Solubility in / Miscibility with water:NOT MISCIBLE
    Partition coefficient: n-octanol/water:Not determined
    Viscosity: Dynamic at 20°C:100 mPas
    Viscosity: Kinematic:Not determined
    Solvent content: Organic solvents:68.4% - Water 0.7%
    Solids content:30.9%



    Health & Safety


    • Refer to the safety data sheet in the attachments section above and tin label prior to use.

    Click to go back to the top of the page

    Product Details
    4445-690264

    Data sheet

    Manufacturer
    HMG Paints Limited
    Water / Solvent Based
    Solvent
    Application Method
    Brush
    Sheen
    Matt
    Colour
    Clear
    VOC Levels
    Low (50-149 g/l)
    Single, Two or Three Pack
    Single
    Product Certifications
    Food contact
    Pack Size
    5L
    Mixing Ratio
    Ready for use
    Suitable Substrates
    Wood & metal
    Dry to Recoat (at 20°C)
    After hard dry
    Fully Cured (at 20°C)
    20 - 30 minutes
    Recommended Thinner/Cleaner
    Thinner 2761
    Density
    0.882 g/cm³
    Solids by Volume
    30.9%
    Heat Resistance (up-to)
    50°C
    VOC
    0.6kgs/ltr
    Shelf Life (from date of manufacture)
    12 months from delivery date in original sealed containers.
    UN Number
    UN1263
    Suitable For Use On
    Metal
    Suitable For Use On
    Wood
    Finish
    Gloss
    Application Method
    Brush
    Product Usage Type
    Sealer
    Colour Family
    Clear
    Attachments
    Download


    Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


    Be the first to ask a question about this product!


    Question about the product

    * Required fields
    (read)
    Send

    IMPORTANT SHIPPING & DELIVERY INFORMATION

    HMG AIF630 Button Polish is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

    Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

    Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

    All delivery costs below are excluding VAT


    You might also like

    HMG Thinner 2671

    HMG Thinner 2671 is an alcohol based thinner.For use in recommended HMG systems.More Information Delivery Info

    Price £11.26 (ex. VAT)
    In Stock and Available for Delivery