- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
Jotun Alkydprimer is a one component, single pack oxidatively drying alkyd coating that can be used as primer or mid coat in atmospheric environments. Suitable for properly prepared carbon steel, aluminium and wooden substrates, this alkyd primer is ideal for a wide range of industrial structures or for touch up areas in the marine industry.
Alkyd Primer
Jotun Alkydprimer can be used as a primer or mid coat in marine and atmospheric environments. This alkyd coating is generally used for touch-up work and small scale purposes within the marine industry and will also act as a protective coating for a wide range of industrial structures - carbon steel and aluminium.
Please download the attached datasheet for more technical information, including further application specifications, drying and curing times, heat resistance and product compatibility.
- Reduces application cost
- Resistant to dry heat up to 120°C
When applying this alkyd primer, the surface should always be clean, dry and free-from loose materials and contamination. General surface preparation guidelines are included in the datasheet for wood, carbon steel and aluminium.
Jotun Alkyd Primer can be applied by spray, brush or roller - with rollers needing extra care to achieve the specified dry film thickness.
Jotun Thinner No. 2 should be used as the thinner and cleaning solvents for Jotun Alkydprimer.
Reduces application cost and waste
Alkydprimer requires no mixing and has no pot life restrictions, which reduce your application cost, waste and leftover paint.
Application
Can be applied to any surface of new or aged coatings in atmospheric conditions - also in conjunction with Pilot II as a topcoat or finish coat.
Data sheet
- Manufacturer
- Jotun
- For Use By
- Professional Use
- Water / Solvent Based
- Solvent
- For Use On
- Steel, Aluminium, Wood
- Application Method
- Spray, Airless Spray, Brush
- Sheen
- Matt
- Colour
- Standard / Ready Mixed
- Single, Two or Three Pack
- Single
- Product Certifications
- Low Flame Spread in accordance with EU Directive for Marine Equipment,
- Pack Size
- 5L, 20L
- Coverage
- 10.4 - 17.3m² per litre
- Touch Dry
- 3 hours
- Base Type
- Solvent
- Suitable For Use On
- Industrial Structures
- Suitable For Use On
- Aluminium
- Suitable For Use On
- Atmospheric Environments
- Suitable For Use On
- Wood
- Suitable For Use On
- Carbon Steel
- Finish
- Matt
- Application Method
- Brush
- Application Method
- Spray
- Product Usage Type
- Primer & Midcoat
- Product Range
- Alkydprimer
- Colour Family
- White
- Colour Family
- Grey
- Colour Family
- Black
- Colour Family
- Red
- Categorised As
- Marine Paints > Low Temperature Primers & Undercoats
- Seasonal
- Cold Weather
Amit singh chandel on 2022-12-06 13:23:13 | Question:
Can I paint this as 2nd coat primer on top of jotamastic component A RED PRIMER |
Answer from Rawlins’ Technical Team:
No this should not be used over a 2 part primer. Jotun Jotamastic products are two part, if only component A has been applied it will not cure and must be removed. | |
Julian Brett on 2022-01-25 07:35:59 | Question:
I'm painting my boat hull, top part not antifoul, and like the look of the Jotun Pilot2 gloss. Is this suitable? What primer should I use, if it is? The boat is GRP and it will be it's first coat of paint over the original gel coat. Also, the existing antifoul is a bit flakey. I've removed all the loose paint but is it worth using a primer on this too, if there's one suitable for both the top and bottom of the hull? One pack if possible. |
Answer from Rawlins’ Technical Team:
No, for application to the existing gelcoat above the water line assuming it is clean, dry, sound and prepared as detailed in the technical data sheet we would recommend 1 coat of Jotun Penguard HB followed by 1 coat of either of the following topcoats depending on the sheen you require. Jotun Hardtop XP or Jotun Hardtop Flexi or Jotun Hardtop AX. For the areas below the water line, they should be cleaned with a pressure washer prior to preparation then application of 3 brush coats of Jotun Penguard HB followed by 1 roller coat of Jotun Vinyguard Silvergrey 88 then 2 brush coats of Jotun Mare Nostrum SP.. | |
james lean on 2016-05-14 15:21:09 | Question: I am looking for primer for aluminium below the waterline, under antifouling coat. Is this suitable? Jus to touch in on existing bare patches, not to coat a new surface. |
Answer from Rawlins’ Technical Team: The primer we recommend for prepared aluminium (cleaned and lightly abraded), which can then be overcoated with antifouling paint is Jotun Safeguard Universal ES however this product is only available in 18L drums. | |
IMPORTANT SHIPPING & DELIVERY INFORMATION
Jotun Alkydprimer is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
Jotun Thinner No. 2
Jotun Thinner No. 2 is a paint thinner designed to improve the flow of a range of Jotun alkyd and oil based based products. It can also be used as cleaner of pumps and tools after and before painting.
Surface Preparation Kits for Steel
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...