- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
3 component, abrasion resistant, polyamine cured epoxy anti-skid coating for approved primers or directly on concrete substrates - such as helidecks, walkways, ramps, weigh bridge decks, decks in general where abrasion resistance and non-slip properties are required.
Jotun Jota Armour is a three component, abrasion resistant, polyamine cured epoxy coating specially designed as an anti-skid coating. Suitable for approved primers or directly on concrete substrates.
Jotun Jota Armour can be used on helidecks, walkways, ramps, weigh bridge decks, decks in general where abrasion resistance and non-slip properties are required.
Approvals and certificates
- Approved to UK Defence Standard 80-134/1 for the Royal Navy, flight decks, hangar decks and weather decks
- Pre-qualification testing in acordance with NORSOK M-501, Rev. 5, System 4, suitable for decks and walkways.
Additional certificates and approvals may be available on request.
Features & Benefits
- Spray application – no trowelling
- High build – one coat system
- Non-slip surface
- non-slip performance in wet, oily and icy conditions
Rough and tough
Jota Armour combines a high solids, surface tolerant . abrasion resistant, epoxy coating with a selected blend of fused aluminium oxide.
High coefficient og friction (COF)
The surface profile is rough with deep and sharp asperities – creating a high COF that provides exceptional non-slip properties for people and equipment even when applied on a sloping ramp or walk-way.
NORSOK pre-qualification
Baltoflake is pre-qualified in NORSOK coating systems (System no.4).
Data sheet
- Manufacturer
- Jotun
- For Use By
- Professional Use
- Interior / Exterior Use
- Exterior Use
- Water / Solvent Based
- Solvent
- For Use On
- Concrete, Metal
- Application Method
- Gravity Feed Hopper Gun
- Colour
- Standard / Ready Mixed
- Single, Two or Three Pack
- Two-Pack
- Product Certifications
- UK Defence Standard 80-134/1, NORSOK M-501
- Pack Size
- 9L
- Coverage
- 0.3 to 1.2m²/l
- VOC
- 144 g/l
- Touch Dry
- 5 hours
- UN Number
- 1263
- Base Type
- Solvent-Based
- Suitable For Use On
- Metal Decks
- Suitable For Use On
- Concrete Decks
- Suitable For Use On
- Metal Ramps
- Suitable For Use On
- Hangar Decks
- Suitable For Use On
- Weather Decks
- Suitable For Use On
- Flight Decks
- Suitable For Use On
- Concrete Walkways
- Suitable For Use On
- Metal Walkways
- Suitable For Use On
- Metal
- Suitable For Use On
- Concrete
- Suitable For Use On
- Concrete Ramps
- Suitable For Use On
- Walkways
- Suitable For Use On
- Helidecks
- Suitable For Use On
- Ramps
- Suitable For Use On
- Weigh Bridge Decks
- Suitable For Use On
- Decks
- Finish
- Semi-Gloss
- Application Method
- Gravity Feed Hopper Gun
- Components
- 3K
- Product Usage Type
- Topcoat
- Product Range
- Jota Armour
- Colour Family
- Grey
- Colour Family
- Green
- Colour Family
- Yellow
Questions
Question about the product
Merlin on 2023-07-11 11:09:57 | Question:
Hi how many 9lt packs would be sufficient to paint 150m2 M |
Answer from Rawlins’ Technical Team:
The coverage rate for this product is 0.3 to 1.2m² per litre depending on the application. For 150m² you would require approximately 500ltrs to 125ltrs. | |
Nabeel on 2022-10-04 11:51:46 | Question:
can this be applied to an exterior timber walkway? will a primer be required before hand? can this be apply by brush/roller? |
Answer from Rawlins’ Technical Team:
Unfortunately no, this is not suitable for application to timber. | |
ian on 2022-03-10 11:05:26 | Question:
I have been sent Jotun Jota Armour. There are 3 cans but no instruction for mixing, application etc. Also it will be painted on existing grey non slip deck paint and raw aluminium. Will I need a primer for the areas that the old paint had flaked and it is down to bare alu? |
Answer from Rawlins’ Technical Team:
Yes a 2 pack primer such as Jotun Jotamastic 90 which is suitable for application to prepared aluminium, carbon steel or old compatible existing coatings. Approximately 200 microns should be applied. The existing coatings must also be 2 pack to be suitable to be over painted. A solvent rub test should be undertaken if it is not known if the previous coating is 2 pack using Jotun Thinner No. 17. Leave a rag soaked in the thinners on the painted area for 5mins, if the paint coating reacts, unfortunately a two pack paint will not be suitable for this application unless the previously applied paint is removed. | |
IMPORTANT SHIPPING & DELIVERY INFORMATION
Jotun Jota Armour is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT