- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
2-3mm, self-levelling, epoxy screed. Designed to provide a hard wearing, impervious, seamless floor finish which is hygienic and easy to clean.
- Fast application and cure.
- Available in a range of colours.
- Also available in 4,000+ RAL, NCS, and British Standard colours.
- See 306 Self Levelling Floor Coating - Special Colours.
- Three pack product.
- Excellent chemical resistance.
- Very good adhesion to concrete.
- Suitable for use in laboratories, pharmaceutical plants, hospitals, food preparation areas, electronic assembly factories, etc.
- Images are for illustrative purposes only and may differ from the actual product.
- This product is for Professional Use Only.
Product customisation
Don't forget to save your customization to be able to add to cart306 Self Levelling Floor Coating is a 2-3mm, self-levelling, epoxy screed. 306 Self Levelling Floor Coating has been designed to provide a hard wearing, impervious, seamless floor finish which is hygienic and easy to clean.
306 Self Levelling Floor Coating with its combination of attractive finish and excellent resistance to many chemicals, is suitable for a wide range of industrial environments.
306 Self Levelling Floor Coating is typically applied at thicknesses of between 2 and 3mm. It is supplied as a three pack product, consisting of an epoxy resin component, a curing agent component and a graded filler component, all pre-weighed and ready for mixing.
Suitable for use in laboratories, pharmaceutical plants, hospitals, food preparation areas, electronic assembly factories, etc.
This product is for Professional Use Only.
Quick Links - Click To Jump To Section:
- Features & Benefits
- Typical Properties
- Coverage
- Surface Preparation
- Application
- Cleaning
- Curing
- Limitations
- Storage & Shelf Life
- Health & Safety
Features & Benefits
- Self-Levelling
- Hard wearing
- Seamless
- Hygienic and easy to clean
- Attractive finish
- Excellent resistance to many chemicals
- Suitable for a wide range of industrial environments
- Three pack product
- Fast application and cure
- Very good adhesion to concrete
- Range of colours available
Typical Properties
Technical Data | |
---|---|
306 Self Levelling Floor Coating | |
Pot Life: | 50 minutes @ 20°C |
Compressive Strength: | 60 MPa |
Flexural Strength: | 34 MPa |
Chemical Resistance | |
---|---|
Chemical | Resistance |
20% Hydrochloric Acid | Excellent |
10% Sulphuric Acid | Excellent |
20% Sodium Hydroxide | Excellent |
Petrol | Excellent |
Lactic Acid | Excellent |
Bleach | Excellent |
Please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected] for specific advice.
Coverage
- A 25kg pack is sufficient to cover an area of 7m² at a thickness of 2mm
Surface Preparation
- All surfaces should be sound, clean, and free from dust, dirt, laitance, oil and other contaminants
- All laitance must be removed by vacuum grit blasting ensuring that any residual dust is removed
- New concrete surfaces must be a minimum of 21 days old and/or have a residual moisture content below 6%
- Steel substrates shall be grit blasted to Sa 2.5 Swedish Standard, and degreased using 109 Tool Cleaner
Note: Substrates with high moisture content or oil contamination can still be coated in most instances by the inclusion of one of our specialist primers.
Please see 402 Damp Proof Coating and 403 Oil Tolerant Primer for full details.
Priming:
- Prime the prepared surfaces using 405 Tack Primer, applying the material at a nominal rate of 5m²/kg
- Allow the primer to cure overnight
Note: If the surface is exceptionally porous it may be necessary to 'double prime'.
Mixing:
- 306 Self Levelling Floor Coating is supplied as a three component product, each component being preweighed ready for use
- The contents of the curing agent container should be drained into the base component and the two materials thoroughly mixed
- The mixed liquid should then be poured into a forced mixer, e.g. Mixall, Pennine or Creteangle, and the filler component slowly added under constant mixing until a uniform consistency has been achieved
Mixing Ratio:
- By Volume = 3 Base : 1 Curing Agent
- By Weight = 100 Base : 35.1 Curing Agent
Application
- Apply the mixed 306 Self Levelling Floor Coating by serrated trowel or screed box
- Within 20 minutes, spike roller the 306 Self Levelling Floor Coating in order to de-aerate it
- Existing joints in the floor must be carried through the screed
- Always maintain a wet edge to the material during application
Cleaning
- Clean equipment with 109 Tool Cleaner prior to curing of the coating
Curing
- Light foot traffic may be allowed after 24 hours drying @ 20°C and full trafficking after 48 hours @ 20°C
- Optimum chemical resistance will be achieved after 48 hours @ 20°C
Note: At higher temperatures the above cure times will be reduced, at lower temperatures they will be increased
Limitations
- Do not apply to uncured or contaminated surfaces
- Do not apply at temperatures of 5°C or less
Storage & Shelf Life
- Store in dry conditions, out of direct sunlight, at temperatures between 10°C and 20°C
- 306 Self Levelling Floor Coating has a minimum shelf life of 12 months when stored in original, unopened containers in accordance with manufacturer’s instructions
Health & Safety
- Avoid contact of the material with skin and eyes
- Wear gloves and goggles
- Wash off splashes immediately with soap and water
- Any eye contamination must be rapidly irrigated with copious amounts of water, and immediate medical attention sought
- Please refer to Material Safety Data Sheet for additional Information
- 306 Self Levelling Floor Coating shall be applied strictly in accordance with the manufacturer’s instructions
For specific advice regarding any aspect of this product, please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected]
Data sheet
- Manufacturer
- Rawlins Paints
- For Use By
- Professional Use
- Interior / Exterior Use
- Interior Use
- Water / Solvent Based
- Solvent
- For Use On
- Concrete, Steel
- Application Method
- Trowel, Spiked Roller
- Colour
- Standard / Ready Mixed
- Single, Two or Three Pack
- Three-Pack
- Minimum Applied Thickness
- 2mm
- Maximum Applied Thickness
- 3mm
- Pot Life (at 20°C)
- 50 mins
- Coverage
- 7m² per 25KG
- Min. Application Temperature
- 6°C
- Touch Dry
- 24 Hours
- UN Number
- UN3082, UN2735
- Resistance to chemicals
- 20% hydrochloric acid, 10% sulphuric acid, 20% sodium hydroxide, petrol, lactic acid and bleach
- Suitable For Use On
- Concrete
- Suitable For Use On
- Steel
- Finish
- Gloss
- Application Method
- Roller
- Application Method
- Trowel
- Application Method
- Screed Box
- Components
- 3K
- Product Usage Type
- Self Smoothing Screed
- Product Category
- Paints
- Colour Family
- Blue
- Colour Family
- Red
- Colour Family
- Yellow
- Colour Family
- Black
- Colour Family
- White
- Colour Family
- Grey
- Colour Family
- Green
- Average Application Thickness
- 2-3mm
- Product Type
- Epoxy
Questions
Question about the product
Tonny Hallam on 2018-08-22 10:20:25 | Question:
what would you recommend for the cleaning of equipment i.e mixing drum? |
Answer from Rawlins’ Technical Team:
Clean equipment with 109 Tool Cleaner prior to curing of the coating. | |
IMPORTANT SHIPPING & DELIVERY INFORMATION
306 Self Levelling Floor Coating is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
403 Oil Tolerant Primer
Developed for use in applications to oil contaminated floors prior to application of subsequent floor toppings. The product exhibits outstanding adhesion to concrete and other substrates and is particularly suitable where compromised surfaces exist. Solvent free, low odour Excellent adhesion to concrete and steel Surface tolerant...
405 Tack Primer
An adhesion promoted primer developed for use in conjunction with various epoxy coatings and screed in our range. Solvent free, low odour. Excellent adhesion to concrete and steel. Impervious to water. Low viscosity, easily applied. May be applied to cool, damp surfaces. Pre-packaged units ready for use. Very good chemical resistance....
109 Tool Cleaner
109 Tool Cleaner is a specialist equipment cleaner suitable for the removal of uncured epoxy, polyester and polyurethane resins. Low Hazard Low evaporation rate Excellent solvency powers 80% biodegradable This product is for Professional Use Only Images are for illustrative purposes only and may differ from the actual product More...
402 Damp Proof Coating
2 pack epoxy resin based primer/coating, which has been developed to function as a residual construction moisture suppressant, allowing the early installation of moisture sensitive flooring in fast track building programmes. Also available in 4,000+ colour options from RAL, BS and NCS Please see 402 Damp Proof Coating - Special Colours...