Follow us on:

Sherwin-Williams Macropoxy M262

M262
SHE2178

Sherwin-Williams Macropoxy M262 (formerly Epigrip M262) is a 2-pack epoxy high build gloss finish for interior or exterior use in conjunction with appropriate primers and undercoats. It is suitable for application on concrete floors.

  • Available in 400+ colours, including RAL and BS

Product customisation

Don't forget to save your customization to be able to add to cart
  • 250 char. max
Colour Group
Size
Finish
£144.31(incl. VAT)
£120.26(ex. VAT)
Quantity
Please choose your colour
Available for Delivery (See Delivery Options Below)

Description

Sherwin-Williams Macropoxy M262 (formerly Epigrip M262) is a 2-pack epoxy high build gloss finish for interior or exterior use in conjunction with appropriate primers and undercoats. It is suitable for application on concrete floors.

Endorsements

  • Certified for decontamination EX07190/06/33/01 in accordance with ISO 8690.

Recommended Systems

Compatible with a wide range of Macropoxy, Dura-plate, Zinc Clad Epoxy Primers and Buildcoats. 

Application Conditions & Overcoating

Epoxy paints should preferably be applied at temperatures in excess of 10°C. In conditions of high relative humidity, i.e. 80-85% good ventilation conditions are essential. Substrate temperature shall be at least 3°C above the dew point and always above 0°C.

At application temperatures below 10°C, drying and curing times will be significantly extended, and spraying characteristics may be impaired.

Application at ambient air temperatures below 5°C is not recommended.

In order to achieve optimum water and chemical resistance, temperature needs to be maintained above 10°C during curing.

If it is desired to overcoat outside the times stated on the data sheet, please seek advice of Technical Team. 

Additional Notes

Drying times, curing times and pot life should be considered as a guide only.

The curing reaction of epoxies commences immediately the two components are mixed, and since the reaction is dependent on temperature, the curing time and pot life will be approximately halved by a 10°C increase in temperature and doubled by a 10°C decrease in temperature.

Suitable for application on concrete floors. Ensure that substrate is sound, clean and free from surface contaminants. Moisture content must be less than 7%. The first coat of Macropoxy M262 should be thinned up to 15% with cleanser thinner 5 to assist in sealing the substrate porosity.

Where a non-skid profile is required P515 aggregate should be stirred into the Macropoxy M262 mixed paint, immediately prior to application, at a rate of 1.0kg per 5 ltr unit. Application will then only be possible by brush or roller.

Epoxy Coatings:

Colour Stability: Variable colour stability is a feature of epoxy materials which tend to yellow and darken with age. Therefore any areas touched-up and repaired with the same colour at a later date may be obvious due to this colour change.

When epoxy materials are exposed to ultra-violet light a surface chalking effect will develop. This phenomenon results in loss of gloss and a fine powder coating at the surface which may give rise to colour variation depending on the aspect of the steelwork. This effect in no way detracts from the performance of the system.

Epoxy Coatings - Tropical Use:

Epoxy paints at the time of mixing should not exceed a temperature of 35°C. At this temperature the pot life will be approximately halved. Use of these products outside of the pot life may result in inferior adhesion properties even if the materials appear fit for application. Thinning the mixed product will not alleviate this problem.

The maximum air and substrate temperature for application is 50°C providing conditions allow satisfactory application and film formation. If the air and substrate temperatures exceed 50°C and epoxy

coatings are applied under these conditions, paint film defects such as dry spray, bubbling and pinholing etc. can occur within the coating.
Numerical values quoted for physical data may vary slightly from batch to batch. 

Product Details
2178-861446

Data sheet

Manufacturer
Sherwin-Williams
For Use By
Industrial Use
Interior / Exterior Use
Interior & Exterior
Water / Solvent Based
Solvent
For Use On
Concrete
Application Method
Airless Spray, Conventional Air Spray, Brush, Roller
Sheen
Gloss
Colour
Fully Tintable
Single, Two or Three Pack
Two-Pack
Touch Dry (at 20°C)
90 Mins
Coverage
8.0m² per litre
Touch Dry
1.5 hours
UN Number (Activator)
UN3469
UN Number (Base)
UN1263
Base Type
Solvent-Based
Suitable For Use On
Primed Surfaces
Suitable For Use On
Concrete
Finish
Gloss
Application Method
Roller
Application Method
Brush
Application Method
Spray
Usages
High Build
Usages
Tough/Durable
Usages
Atmospheric
Product Usage Type
Topcoat
Product Range
Macropoxy
Colour Family
Magnolia
Colour Family
Brown
Colour Family
Anthracite Grey
Colour Family
Neutral
Colour Family
Orange
Colour Family
Beige
Colour Family
Yellow
Colour Family
Green
Colour Family
Black
Colour Family
Red
Colour Family
White
Colour Family
Pink
Colour Family
Cream
Colour Family
Violet
Colour Family
Purple
Colour Family
Grey
Colour Family
Off-White
Colour Family
Blue
Product Type
Polyurethane
Environment
Atmospheric
Touch Dry/Dust Free (@ 20-25°C)
90 mins
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


questions Colin Brown on 2022-08-11 08:31:08
Question: 

Hi M262 - Maximum overcoating time when applying multiple coats.

Answer from Rawlins’ Technical Team: 

At 150°C this can be recoated in 6hours, at 23°C it can be recoated in 4 hours.

questions Iain on 2017-06-01 16:56:06
Question: Can you supply undercoat for this product (M262)? Thanks Iain
Answer from Rawlins’ Technical Team: 

Sherwin-Williams Macropoxy M262 is compatible with a wide range of Macropoxy, Dura-plate, Zinc Clad Epoxy Primers and Buildcoats.


Question about the product

* Required fields
(read)
Send

IMPORTANT SHIPPING & DELIVERY INFORMATION

Sherwin-Williams Macropoxy M262 is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

All delivery costs below are excluding VAT


COVERAGE CALCULATOR
Units
Total area²
Or enter length and width dimensions:
Length
Width

*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage