- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
Britannia Zinc Phosphate Metal Primer is an anti-corrosive primer for use on ferrous metal surfaces including iron and steel.
- Superb capacity and coverage
- Higher solids primer
- Contains zinc phosphate for added corrosion protection
- Can be used over sound existing paintwork
- Can be brush, roller (solvent resistant) or spray applied
- Solvent based
- Exterior use
Britannia Zinc Phosphate Metal Primer is a one pack solvent-based primer for use on ferrous metal surfaces such as iron and steel. It offers superb capacity and coverage and the product contains zinc phosphate for added corrosion protection.
Britannia Zinc Phosphate Metal Primer is an anti-corrosive high solids primer which can be brush, roller (solvent resistant) or spray applied.
For external use.
Quick Links - Click To Jump To Section:
- Features & Benefits
- Spreading Rate
- Drying Times
- Preparation
- Application
- Cleaning
- Shelf Life & Storage
- Precautions
Features & Benefits
- Solvent-based
- One-pack
- For use on ferrous metal surfaces such as iron and steel
- Superb capacity and coverage
- Contains zinc phosphate for added corrosion protection
- Can be brush, roller (solvent resistant) or spray applied
- Anti-corrosive high solids primer
- For external use
Spreading Rate
These will vary depending on substrate, the site conditions and longevity required.
Typically spreading rates will vary depending on the end use.
- Up to 13m²/litre @ 35 microns dft minimum
- Should be applied at 5°C and above
Drying Times
Drying Times @ 20 °C | |
---|---|
Touch Dry | 30mins |
Through Dry | 6 hours |
Overcoating Times @ 20 °C | |
Minimum | 2 hours |
Maximum | Indefinite |
Note: If primer is not overcoated within 14 days then abrade with either P240-P320 and clean with a spirit wipe.
- Curing of the coating can be extended at lower temperatures
Preparation
- Ensure all areas are clean, dry and free from dust, dirt, corrosion and general surface contamination.
- All oils, grease, etc should be removed with a suitable degreasing solution.
- Degreasing with a spirit wipe is recommended and should be carried out after any abrasion of the surface.
Steel:
- Should preferably be abrasion blast cleaned to BS 7079 Standard SA2.5
- Thorough mechanical preparation (e.g. power wire brushing, needle gunning, grinding etc) can be utilised for mild environments
Sound Existing Paintwork:
- Dry sand using P320-P240
Application
- Do not thin.
- Stir well before use
- Please follow the coverage rates shown in Spreading Rate Section
Cleaning
- Remove as much primer as possible from application equipment before cleaning
- For cleaning equipment use special solvent (not white spirit)
Shelf Life & Storage
- Up to one year in an unopened original container at moderate temperatures
- Store in a safe place in accordance with the instructions in section 7 of the relevant MSDS sheet
Precautions
- Flammable keep away from sources of ignition
- Ensure good ventilation during application
- Wear gloves, goggles and suitable protective clothing
- In case of contact with eyes rinse immediately with plenty of water and seek medical advice
- Remove splashes from the skin with a recognised hand cleaner or plenty of soap and water
- Keep out of reach of children
- Do not use near fishponds
- Toxic to aquatic organisms
- May cause long term adverse effects in the aquatic environments
- Do not empty into drains
Data sheet
- Manufacturer
- Britannia
- Water / Solvent Based
- Solvent
- For Use On
- Iron, Steel, Ferrous Metals
- Application Method
- Brush, roller, spray
- Colour
- Standard / Ready Mixed
- Single, Two or Three Pack
- Single
- Pack Size
- 1L, 5L
- Dry to Recoat (at 20°C)
- 2 hrs
- Coverage
- Up to 13m²/litre @ 35 microns dft minimum
- Touch Dry
- 30 minutes
- UN Number
- UN1263
- Base Type
- Solvent-Based
- Suitable For Use On
- Iron
- Suitable For Use On
- Ferrous Metals
- Suitable For Use On
- Steel
- Application Method
- Roller
- Application Method
- Brush
- Application Method
- Spray
- Product Usage Type
- Primer
- Colour Family
- White
- Colour Family
- Grey
Aneeta Mary Joseph on 2024-05-16 14:54:42 | Question:
Can the zinc phosphate primer be applied on top of already existing paint systems which has partially deteriorated? And then surface preparation done to SA21/2? Current coatings are epoxy and polyurethane based. |
Answer from Rawlins’ Technical Team:
Thank you for the enquiry, please can you provide more information on the application and products in question to [email protected] so we can look into this for you. | |
IMPORTANT SHIPPING & DELIVERY INFORMATION
Britannia Zinc Phosphate Metal Primer is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT