- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
Bradite Fastrac Rust Converter is a high performance, single-pack, water-based rust converter intended for the treatment and passivation of surface rust on all hand or mechanically prepared rusty ferrous surfaces.
- Especially suited for objects which may be difficult to sand blast such as; fences, iron railings, guttering and outdoor fixtures
- Manufactured under the auspices of an ISO 9001:2008 quality & ISO 14001:2004 environmental management systems
Quick Links - Click To Jump To Section:
Features & Benefits
- High performance single pack water based rust converter
- Intended for the treatment and passivation of surface rust on all hand or mechanically prepared rusty ferrous surfaces
- Especially suited for objects which may be difficult to sand blast such as; fences, iron railings, guttering and outdoor fixtures
- Suitable for use on wire brushed or mechanically abraded surfaces which are free from heavy rust scale, grease and dirt
- White colour turns black on contact with rust
- Manufactured under the auspices of an ISO 9001:2008 quality & ISO 14001:2004 environmental management systems
Application
- Application and use should always conform to the codes of practice described in BS 6150 and BS 5493
- Stir thoroughly before use
- Applicable by brush, roller, conventional air spray or airless spray. Brush application is strongly recommended and is the preferred application method for best performance:
- Brush and Roller - Supplied ready for use. Thin with 0 - 5% water if required
- Conventional Air Spraying - Thin with 10 - 20% water as required, tip size - 2.0mm, tip pressure 60psi
(0.4MPa) approximately - Airless Spraying - Thin with 0 - 15% water as required, tip size - 18 thou (0.46mm) approximately, tip pressure
- 2100 psi (15MPa) approximately
- Apply 1 full coat @ 30 microns/WFT or 20 microns/DFT
- 20 m2/L/coat theoretical coverage rate
- Clean all equipment immediately after use with water for best results
Data sheet
- Manufacturer
- Bradite
- For Use By
- Consumer Use
- Interior / Exterior Use
- Exterior Use
- Water / Solvent Based
- Water
- For Use On
- Ferrous metals
- Application Method
- Brush
- Sheen
- Eggshell
- Colour
- Standard / Ready Mixed
- VOC Levels
- Ultra-Low (5-49 g/l)
- VOC Levels
- 29 g/L
- Single, Two or Three Pack
- Single
- Product Certifications
- ISO 9001:2008, ISO 14001:2004 environmental management systems
- Pack Size
- 1L
- Dry to Recoat (at 20°C)
- 3 hours - unlimited
- Fully Cured (at 20°C)
- 7 days
- Coverage
- 20m2 per Litre
- Recommended Thinner/Cleaner
- Water
- Min. Application Temperature
- Down to 10°C & 60% RH maximum (but must be 3°C above dew point)
- Density
- 1.00 kg/L
- Solids by Volume
- 65%
- Shelf Life (from date of manufacture)
- 12 months minimum in original unopened containers
- Touch Dry
- 20-30 Mins
- Recommended Dry Film Thickness
- 20 microns/coat
- Recommended Wet Film Thickness
- 30 microns/coat
- Flammability
- Non flammable
- Colour(s)
- White (turns black on contact with rust)
- Base Type
- Water-Based
- Suitable For Use On
- Ferrous Metals
- Finish
- Eggshell
- Application Method
- Spray
- Application Method
- Brush
- Application Method
- Roller
- Usages
- Atmospheric
- Usages
- Rust Converter
- Product Usage Type
- Rust Converter
- Colour Family
- White
- Dry to Recoat (@ 20-25°C)
- 3 hours
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Bradite Fastrac Rust Converter is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT