- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
Carboline Carbomastic 18 FC Metallic is a two-component, heavy duty, high build coating for protection of steel in corrosive environments, and is excellent for use at low temperatures.
- Excellent immersion performance in both fresh and sea water
- Suitable as a rust preventing coating in ballast tanks
- Ideal for subsea installations, jackets, and other areas prone to condensation
- Very good abrasion resistance
This product is only available as PRICE ON APPLICATION - For more information and to place an order please contact us on 0113 2455450 or email [email protected].
Carboline Carbomastic 18 FC Metallic is a two-component, heavy duty, high build coating for protection of steel in corrosive environments. Carbomastic 18 FC Metallic is excellent for use at low temperatures.
Click To Jump To Section:
- Features and Benefits
- Product Specification
- Drying Times
- Surface Preparation
- Application Methods
- Application Conditions
- Health and Safety
Features and Benefits
- Excellent immersion performance in both fresh and sea water
- Suitable as a rust preventing coating in ballast tanks
- Ideal for subsea installations, jackets, and other areas prone to condensation
- Very good abrasion resistance
Product Specification
Technical Data | ||||||
---|---|---|---|---|---|---|
Carboline Carbomastic 18 FC Metallic | ||||||
Volume Solids: | 90 ± 2% | |||||
Theoretical Coverage Rate: | 5,1 m²/l at 175 µm | |||||
Allow for loss in mixing and application | ||||||
Dry Film Thickness: | 125 - 500 microns (4.92 - 19.68 mils) per coat | |||||
Normally 175 µm | ||||||
Wet Film Thickness: | 140 - 555 µm per coat, normally 195 µm | |||||
Dry Temperature Resistance: | Continuous: 120°C (248°F) | |||||
Non-Continuous: 150°C (302°F) | ||||||
Topcoats: | Normally not topcoated for submerged exposures, otherwise topcoat according to Carboline recommendations | |||||
Limitations: | Epoxies discolour and eventually chalk in sunlight exposure | |||||
Not recommended for immersion in aromatic or ketone solvents or strong oxidizing acids | ||||||
Shelf Life: | 24 months at 24°C | |||||
Storage Temperature and Humidity: | 40°F-110°F (5°-45°C) | |||||
0 - 95% relative humidity |
Drying Times
Curing Schedule | ||||||
---|---|---|---|---|---|---|
Surface Temp. | Dry to Recoat | Final Cure | ||||
5°C (41°F) | 17 Hours | 15 Days | ||||
10°C (50°F) | 10 Hours | 12 Days | ||||
15°C (59°F) | 6.5 Hours | 9 Days | ||||
20°C (68°F) | 4 Hours | 7 Days | ||||
25°C (77°F) | 3 Hours | 5 Days |
- Maximum recoating time is 1-2 months depending on temperature and curing conditions. If exceeded, contact Rawlins on Tech - 0113 2455450 (option 2) or [email protected] for further information about recoating procedures
Surface Preparation
General
- Surfaces must be clean and dry
- Employ adequate methods to remove dirt, dust, oil and all other contaminants that could interfere with adhesion of the coating
Steel
- For immersion service, abrasive blast cleaning to min. Sa 2 (ISO 8501-1)
- For non-immersion service, hand- or power tool cleaning to min. St 2 (ISO 8501-1) is acceptable
- Alternatively, ultra-high pressure water jetting to Nace No. 7 min. C Vis WJ-2. Max flash rust; C Vis WJ-2M
Application Methods
Product Information | |||||
---|---|---|---|---|---|
Mixing: | Power mix separately, then combine and power mix. Do not mix partial kits | ||||
Thinning: | Up to 15% with Thinner 2 | ||||
Ratio: | 1:1 Ratio (Part A to B) by Volume | ||||
Pot Life: | 2 Hours at 75°F and less at higher temperatures. | ||||
Airless Spray: | Pump Ratio: 30:1 min | ||||
Volume Output: 3.0 gpm min | |||||
Material Hose: 3/8” I.D. min | |||||
Tip Size: 019-025” | |||||
Output Pressure: 2400 psi | |||||
Filter Size: 60 mesh | |||||
Brush and Roller: | For small areas and stripe coating only. Multiple coats may be required to obtain desired appearance, recommended dry film thickness and adequate hiding | ||||
Brush: | Use a medium bristle brush | ||||
Roller: | Use a medium nap phenolic core roller |
Application Conditions
Product Conditions | |||||
---|---|---|---|---|---|
Condition | Material | Surface | Ambient | Humidity | |
Minimum | 5°C (41°F) | 2°C (35°F) | 2°C (35°F) | 0% | |
Maximum | 35°C (95°F) | 50°C (122°F) | 40°C (104°F) | 85% |
- Industry standards are for substrate temperatures to be 5°F above the dew point
- Condensation due to substrate temperatures below the dew point can cause flash rusting on prepared steel
- Special application techniques may be required above or below normal application conditions
Health and Safety
Clean Up
- Use Thinner 2 or Acetone
- In case of spillage, absorb and dispose of in accordance with local applicable regulations
Safety
- Read and follow all caution statements on this product data sheet and on the safety data sheet for this product
- Employ normal workmanlike safety precautions
Ventilation
- When used as a tank lining or in enclosed areas, thorough air circulation must be used during and after application until the coating is cured
- The ventilation system should be capable of preventing the solvent vapor concentration from reaching the lower explosion limit for the solvents used
Caution
- This product contains flammable solvents. Keep away from sparks and open flames
- All electrical equipment and installations should be made and grounded in accordance with the applicable local regulations
- In areas where explosion hazards exist, workmen should be required to use non-ferrous tools and wear conductive and non-sparking shoes
- Refer to the product and safety data sheet in the attachments section above for further details
Data sheet
- Manufacturer
- Carboline
- For Use On
- Steel
- Application Method
- Brush, Roller, Spray
- Sheen
- Semi-Gloss
- Colour
- Standard / Ready Mixed
- Single, Two or Three Pack
- Two-Pack
- Pack Size
- 20L
- Mixing Ratio
- 1:1 Ratio (Part A to B) by Volume
- Dry to Recoat (at 20°C)
- 4 Hours
- Fully Cured (at 20°C)
- 7 Days
- Coverage
- 5,1 m²/l at 175 µm
- Recommended Thinner/Cleaner
- Carboline Thinner 2
- Compatible Topcoats
- Normally not topcoated for submerged exposures, otherwise topcoat according to Carboline recommendations
- Max. Application Temperature
- Material: 35°C (95°F) - Surface: 50°C (122°F) - Ambient: 40°C (104°F) - Humidity: 85%
- Min. Application Temperature
- Material: 5°C (41°F) - Surface: 2°C (35°F) - Ambient: 2°C (35°F) - Humidity: 0%
- Solids by Volume
- 90 ± 2%
- Shelf Life (from date of manufacture)
- 24 months at 24°C
- Recommended Dry Film Thickness
- 125 - 500 microns (4.92 - 19.68 mils) per coat
- Recommended Wet Film Thickness
- 140 - 555 µm per coat, normally 195 µm
- UN Number (Activator)
- UN3469
- UN Number (Base)
- UN1263
- Dry to Recoat (at 10°C)
- 10 Hours
- Fully Cured (at 10°C)
- 12 Days
- Pot Life
- 2 Hours at 75°F and less at higher temperatures
- Base Type
- Solvent-Based
- Suitable For Use On
- Steel
- Finish
- Semi-Gloss
- Application Method
- Brush
- Application Method
- Roller
- Application Method
- Spray
- Usages
- Corrosion Resistance
- Usages
- Low Temperature
- Usages
- Surface Tolerant
- Usages
- Atmospheric
- Usages
- Anti-Corrosive
- Usages
- MIO
- Usages
- Immersion
- Usages
- Heavy Duty
- Usages
- Direct to Metal
- Usages
- High Build
- Usages
- Abrasion Resistant
- Product Usage Type
- Topcoat
- Product Range
- Carbomastic
- Categorised As
- Metal Paints > Low Temperature Direct-to-Metal Paints
- Seasonal
- Cold Weather
- Product Type
- Modified Epoxy
- Environment
- Low Temperature
- Environment
- Immersion
- Environment
- Atmospheric
- Product Attributes
- High Build
- Product Attributes
- Anti-Corrosive
- Product Attributes
- Heavy Duty
- Resistance to
- Corrosion
- Resistance to
- Abrasion
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Carboline Carbomastic 18 FC Metallic is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
Carboline Thinner 2
Carboline Thinner 2 is a thinner for use in industrial coatings.
Surface Preparation Kits for Steel
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...