- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
4,000+ matt and eggshell colours for use over Thermoguard Timbercoat or Thermoguard Timbercoat Insulating Basecoat.
- Topcoat and maintenance paint for timber surfaces protected with Thermoguard Timbercoat.
- Emits a safe fire-damping vapour in a fire to control flame spread and suppress smoke.
- As part of a complete system achieves 30 or 60 mins Fire Resistance and BS EN Class B s1 d0.
- Internal and external use.
Important!
- Should be used in most instances as one part of the following systems:
- Please note should you be unsure whether this product/system is suitable for your requirements please see below.
Product customisation
Don't forget to save your customization to be able to add to cartPlease note should you be unsure whether this product/system is suitable for your requirements please download and complete the 'Thermoguard Wood Enquiry Form' and return by email to [email protected]
Upon receipt our team will respond within 24-48 hours with specification/advice on our best suggestion for your project. If you have any questions regarding this process consult our technical department on 0113 2455450 (option 2).
Thermoguard Smoke & Flame Retardant Dualcoat is a decorative finish and maintenance paint that can be used as part of a flame and fire retardant system for wood and wood-based boards protected with Thermoguard Timbercoat internally and externally. As part of a complete system it controls surface spread of flame and fire propagation, total smoke control, flaming droplets and particulates to BS EN Class B s1 d0.
When used as instructed with Thermoguard Timbercoat, Thermoguard Smoke & Flame Retardant Dualcoat completes a system that meets new Fire Regulations standard BS EN Class B s1 d0 providing the safest standards for toxic smoke (s1), flaming droplets (d0) and flamespread / insulation Class A2 + B (previous Class 0 compliant). For 30 & 60 minutes Fire Resistance see Thermoguard Timbercoat 30 & 60 Minute System.
- Available in an Acrylic Matt or Acrylic Eggshell finish in the full RAL, BS and NCS colour ranges (excluding fluorescent and metallic shades).
- For 30 & 60 minutes Fire Resistance see Thermoguard Timbercoat 30 & 60 Minute System.
- For fire protection to doors, see Fire Door Paint (30min) or Fire Door Varnish (30min).
- Can be used on suitable external timber cladding. Best to apply to all sides. If not practical, seal void with fire rated foam and acrylic intumescent mastic. (For bare existing porous wood boards, we recommend Thermoproof Exterior).
- Finished system provides a decorators’- acrylic smooth aesthetically pleasing, durable finish to wood, mdf, ply and wood derivatives
Quick Links - Click To Jump To Section:
- How It Works
- Fire Test
- Application
- Drying Times
- Typical Use
- Preparation
- Certificates
- Cleaning
- Health and Safety
How It Works
Timbercoat Insulating Basecoat expands in a fire to create a resilient insulating barrier.
Dualcoat Smoke and Flame Retardant emits a safe fire-damping vapour in a fire to control flame spread and suppress smoke.
Dualcoat SFR’s polyurethane hardened acrylic “cross-links” during the drying process to form a smoother, harder, more cleanable surface than typical decorative paints.
Fire Test
FIRE TEST STANDARDS in UKAS and EOTA - accredited Fire Test laboratory
BS EN Class B s1 d0 (old Class 0 compliant) on wood and wood-based boards
Application
1 or 2 coats as specified over Timbercoat basecoat.
Pack Sizes
Sold in 20, 40 and 80m² pack sizes to aid correct application
Coverage
Follow issued specification or on can guide to enable project Certification.
Drying Times
In normal conditions product will be touch dry in an hour and fully dry after 4 hours
Conditions
Do not apply in temperatures under 8°C or above 30°C.
Maximum relative Humidity below 75%.
Wood should be fully dry. Surface should be at least 3°C above the dew point.
Typical Use
This product forms part of a system for protecting wood and wood-based boards
VOC Content
Low VOC. EU limit for this product (cat A/i) is 140 g/l. This product contains 16 g/lv.
Composition
Catalytic and safe vapour-emission compounds, nano-particle encapsulation-water-based polyurethane hardened cross-linking acrylic
Preparation
Insulating Basecoats must be clean and fully hard dry. Stir well before use.
Brush/Roller application:
Use a woven short pile roller sleeve or synthetic brush at rate stated on can
Spray application:
Pressure Pot and Gun conventional with hand-portable compressor.
Thin 5% water
OR Airless Graco 1500, 3500 or equivalent. 3/8” line, 30 mesh filter on machine, no filter in gun. 521, 523, 621 or 623 tips.
Ensure coverage is applied as per can i.e., 20m² can covers 20 square metres.
Certificates
Once the works are complete, a project and area-specific Certificate is available HERE after due diligence stating any project specification number.
Cleaning
Return as much unused material to its original container as possible. Wash brushes, rollers and guns with clean water immediately following use.
Health and Safety
Please refer to the relevant Safety Data Sheet for full details of this product.
Apply all products according to BS 6150:2019- Buildings Painting Code of Practice
Do not store this product in cold temperatures below 5°C or above 30°C.
Store in a dry secure place away from children or animals.
Dispose of in accordance with local authority waste disposal measures.
Do not pour into drains or watercourses. Reduce- Reuse- Recycle.
Further Support If you require any further assistance, please contact our Technical Department on 0113 2455450 (option 2) or email [email protected]
IMPORTANT FIRE PRODUCTS NOTICE: The information displayed on this website should be used as a guide ONLY and our Technical Department should be contacted to obtain a tailored specification and any advice necessary before you place an order for fire protection products. Fire protection products are non-returnable except in accordance with Condition 8 of the Terms and Conditions and should be applied only by an individual with the necessary expertise and experience. We will not be held liable for any resulting damage to property, human life or monetary costs incurred due to the incorrect specification you have prepared or use of fire protection products caused by your negligence, including your failure to have contacted us to obtain the relevant advice/specification.