Follow us on:

HMG Marine Varnish

HMG Marine Varnish

TOPMARCLE
HMG4385

HMG Marine Varnish is a tough and durable clear gloss formulated on a unique blend of polyurethane alkyds for high quality marine and can be used for industrial finishing.

This product MUST be purchased/used in conjuction with its manufacturer specified base or activator/hardener/thinner:

2-Pack System Details
Base (Part 1) HMG Marine Varnish
Thinner (Part 2) HMG Thinner 2612

  • Part one of a two-pack system
  • Available as a clear
Colour
Size
Finish
£105.22(incl. VAT)
£87.68(ex. VAT)
Quantity
Please choose your colour
Available for Delivery (See Delivery Options Below)

No queries yet, leave the first!
Description

HMG Marine Varnish is a tough and durable clear gloss formulated on a unique blend of polyurethane alkyds for high quality marine and can be used for industrial finishing.

Please note this product is one part of a two-pack system which MUST be purchased/used together with HMG Thinner 2612.



Click To Jump To Section:




Features & Benefits


  • Part one of a two pack system
  • Available as a clear



Product Specification


Technical Data
Volume Solids: 52.4%
VOC Content: 0.460kgs/ltr
SG: -
Viscosity: 260 mPas
Density: 0.909 g/cm³
Storage Conditions: Store between 5°C - 25°C. When not in use, cans must be kept sealed.
Shelf Life: 12 months from delivery date in original sealed containers.
Flash Point: >30°C



Film Thickness Range And Coverage


Product Data
  Dry Film Thickness Wet Film Thickness
Brush: n/a n/a
Compliant Spray Gun: n/a n/a



Coverage: 18.4 square metres per litre @25 microns dft (Theoretical)

  • HMG technical data sheets indicate a dry film thickness that will be achieved when applying a particular wet film thickness.
  • These values are a guide only and are not to be used as specifications.
  • Film thickness will vary depending on actual use and specification.
  • Great care should be taken to achieve the dft stated in the agreed specification and to avoid areas of excessively low or high thickness.



Drying Times


Drying Times At 20°C
Touch Dry: 5 minutes
Dry To Handle: 20 minutes
Dry To Recoat: At any stage of dry.
Fully Cured: 1 hour



Surface Preparation


  • Ensure surfaces to be coated are dry and must be cleaned using the appropriate HMG product to remove all traces of contaminants.



Application Methods


Technical Data
HVLP Compliant Spray Gun
Mixing Ratio: Base: 9.5 Base: 9
Thinner: 0.5 approx Thinner: 1 approx
Thinner Options: Thinner 2612 Thinner 2612
- -
Viscosity: - -
Spray Gun Setup: - 1.4 - 1.6
Number Of Coats (Guide Only): 2 - 3 full coats 2 - 3 full coats
Flash Off: 15 minutes between coats 15 minutes between coats



For further information on mixing ratios please contact Rawlins Paints on Tech - 0113 2455450 (option 2) or [email protected] Sales - 0113 2455450 or [email protected]



Product Notes


Information on basic physical and chemical properties
Form: Liquid
Colour: According to product specification
Odour: Characteristic
Odour Threshold: Not determined
pH-value: Not determined
Change in Condition
Melting point/freezing point: Undetermined
Initial boiling point and boiling range: 135°C
Flash Point: >30°C
Flammability (solid, gas): Not applicable
Ignition temperature: >200°C
Decomposition temperature: Not determined.
Auto-ignition temperature: Product is not selfigniting
Explosive properties: "Product is not explosive. However, formation of explosive air vapour mixtures are possible."
Explosion limits: Lower: 0.6 Vol %
Explosion limits: Upper: 7 Vol %
Vapour pressure at 20°C: 2 hPa
Density at 20°C: 0.909 g/cm³
Relative density: Not determined
Vapour density: Not determined
Evaporation rate: Not determined
Solubility in / Miscibility with water: NOT MISCIBLE
Partition coefficient: n-octanol/water: Not determined
Viscosity: Dynamic at 20°C: 260 mPas
Viscosity: Kinematic: Not determined
Solvent content: Organic solvents: 46.5%
Solids content: 52.4%



Health & Safety


  • Refer to the safety data sheet in the attachments section above and tin label prior to use.
  • Suitable respiratory equipment should be worn when spraying.

Click to go back to the top of the page

Product Details
4385-637379

Data sheet

Manufacturer
HMG Paints Limited
Application Method
Brush, Spray
Sheen
Gloss
Colour
Clear
Single, Two or Three Pack
Two-Pack
Pack Size
5L
Mixing Ratio
HVLP - Base: 9.5/Thinner: 0.5 approx
Mixing Ratio
Compliant Spray Gun - Base: 9/Thinner: 1 approx
Touch Dry (at 20°C)
5 Minutes
Dry to Handle (at 20°C)
20 Minutes
Dry to Recoat (at 20°C)
At any stage of dry
Fully Cured (at 20°C)
1 Hour
Coverage
18.4 square metres per litre @25 microns dft
Density
0.909 g/cm³
Solids by Volume
52.4 %
VOC
0.460kgs/ltr
VOC
0.460kgs/ltr
Shelf Life (from date of manufacture)
12 months from delivery date in original sealed containers
UN Number
1263
Base Type
Alkyd
Base Type
Polyurethane
Finish
Gloss
Application Method
Spray
Application Method
Brush
Product Usage Type
Topcoat
Colour Family
Clear
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

Questions

Question about the product

* Required fields
(read)

Be the first to ask a question about this product!

IMPORTANT SHIPPING & DELIVERY INFORMATION

HMG Marine Varnish is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

All delivery costs below are excluding VAT



COVERAGE CALCULATOR
Units
Film Thickness
Total area²
Or enter length and width dimensions:
Length
Width

*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage

You might also like